flashforge finder glass build plate 3d models
428187 3d models found related to flashforge finder glass build plate.thingiverse
Sliced into 4 parts to fit the finder original bed and added alignment indicators to help with putting pieces together. ... Disclaimer: I have not tested this yet and this is an on going file.
thingiverse
I bought my build plate from the FlashForge web site. It's 1/4" plate glass, which seems a bit thick. I haven't actually printed with it yet, but I will update when I do. My FlashForge has a 75mm wide notch in the back of the Z-Axis mount (behind the...
thingiverse
These clips allow you to mount and secure a glass build plate cut to fit the standard dimensions of the stock build plate of the Flashforge Creator Pro and it's common clones. Just make 2 (one each for opposite corners and secure using the corner...
thingiverse
I found the office supply spring clamps for holding the glass build plate in place difficult to clean around so here is my solution. Added files to build 4 clamps at once, should save folks a bit of print time. ...
thingiverse
So, in the true spirit of printing what I need, I designed a bed to hold the glass plate while it cools. it is designed to hold plates that are 9 inch by 6 inch. It has also been run through NetFabb. I hope it's handy for you..!! ...
thingiverse
You can find out more Information on the aluminum arms @ http://bctechnologicalsolutions.com/replicatorarms Instructions Take the Corel Draw file (CDR), or the DXF File, find a friend or colleague with a laser cutter, and cut out a new plate, and...
thingiverse
Just knocked this up as the previous one I downloaded didn't drain into the vat, this slides on sideways and locks using the plate locking knob, then you just slide your build plate handle on to the hook. ... I've added one with a bit of an angel to...
thingiverse
I have modified the factory flexible plate to use a magnetic PEI plate, but my Y-Axis Has been slipping. After several iterations I was able to make this clips that keep the plate from sliding forward. This should be helpful for anyone using the...
thingiverse
A part to clamp a 3mm glass plate to the Rigidbot Build Plate. I used 16mm M3 Hex nuts with washers to ensure the bolts do not wear through the clamps. Printed using ABS and 50%or more infill. Use a 100% infill a stronger and longer lasting clamp....
thingiverse
I recently purchased a few (8) glass cutting boards from the dollar store that work VERY well for build plates. I needed a way to store them and keep them out of the way at the same time so I designed this around a few pieces of PVC pipe I had and...
thingiverse
This is a small modification to a remix of the original. all credit goes to the original creator. ...just added some holds/pegs for rigidity and alignment.
thingiverse
If you try to reuse the existing nut, you cannot tighten the nut with the glass on the build plate since the bolt will turn...making it really hard to put the clips on correctly so the glass will be centered and the clips are tight against the glass....
thingiverse
... against the glass. The spacer goes right below the z-axis endstop. Make sure that it hits the endstop before putting the glass plate on so the nozzle won't hit the plate. ...I also use a little painter's tape to make sure the plate still won't move.
thingiverse
Well here is an adapter to use the excellent prusa mini magnetic build plates! Uses stock spring, thumbscrews, and bed bolts. No support needed. ... I used these but any round 8x3mm magnet should work https://www.amazon.com/gp/product/B07B3SDRCP/
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1802486 Instructions Using the following options: slot_length = 15 wall_thickness = 4 wall_length = 15 base_length = 27 tab_right = 3 nut_height = 2.5 tab_left = 3 base_thickness = 5...
thingiverse
I wanted to print on a glass plate with my CTC Dual as I had torn the 'stock' Kapton tape that they had pre-installed on the aluminum heated bed. I liked 4KoeTTer's design, but living in the US, I can't get the Metric picture frame glass that he...
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1802486 I customised this to hold my Vellerman 215mm2 glass panel in place on my 220mm2 heated bed, works well, P.S. ...don't use PLA if your gong to be printing ABS they will melt.
thingiverse
This is a newly designed build plate hanger for a FlashForge Foto 8.9" 4K monochrome 3D resin printer.
cults3d
This is a newly designed build plate hanger for a FlashForge Foto 8.9" 4K monochrome 3D resin printer.
thingiverse
Makerbot Replicator 2 Replacement 3/16" Glass Build Plate Adaptor Based on and similar to the adaptor that comes with P3-D's glass build plates.http://www.p3-d.com/products/glass-build-plate
thingiverse
Storage holder for spare glass build plates up to 4mm thick
myminifactory
Tool-shelf for storage of the tools delivered together with the Flashforge Finder
thingiverse
This is a Caliper (Case) Holder for a Flashforge Finder 3D Printer.