flashforge inventor mods 3d models

I wanted a simple and affordable solution for the FlashForge Finder I'm testing. While learning FreeCad, I tried to create a basic way to hold a polycarbonate sheet using small and effective methods. After researching flammability comparisons between...

... the different sides, mirror this file in the slicer. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2-0.3mm Infill: 35% Filament: Hatchbox PLA Notes: It also works in ABS Category: 3D Printer Parts

I redesigned the existing clamp for the Flashforge Creator Pro's feed tube. Since two were provided but one broke, I created a new one that securely snaps into place with high insertion force. It holds the feed tube tightly in position. Printer...

There are four tube retention clamps on the back of the Flashforge Creator, two for each tube. I had one of these hinged clips break off and created this one that's simply a high insertion force press-in, very snug fit. It features a mounting hole...

The model, originally sourced from http://www.thingiverse.com/thing:180757 (with the original design thread found at http://www.thingiverse.com/thing:153807), was integrated into a replica of the plate on top of the extruders for a FlashForge Creator...

I created this to make swapping spools easier without struggling with the holder on the Flashforge.\r\nYou simply need a base plate and print adapters for your spools, which can be left attached to an adapter, allowing you to hang them from the wall...

This bracket holds the Thordsen remote dryer and mounts to the back of a FlashForge Creator Pro on the filament tube clips. There are two clamps, one to hold the dryer and another if you want to use the bracket to just hold the filament tube. The...

Tired of dropping those stupid standoffs that are supposed to go on the back of your Flashforge extruder daughter board? This integrates those standoffs into one easy to install plate. Photos #4 and #5 show the electrical short and damage that...

A simple filament guide that fits the standard openings of the FlashForge Dreamer comes pre-assembled with two rivets for secure attachment. The lid still accommodates optional printed spacers available at http://www.thingiverse.com/thing:1219953,...

I began with m1s2h3's FlashForge Finder Spool Holder modification and enhanced it to incorporate a secondary hook that would cradle a filter on it. I customized the hook to rotate the connector on it to the opposite side, then modified his filament...

I have occasionally had problems with my FlashForge Adventurer 3 having the plate not stay clipped into place, causing a Y-Axis shift in my builds partway through. I designed this simple plate clip that, once printed, can be looped around the...

This is a simple remix of a PTFE cutting tool specifically designed for the Flashforge Finder PTFE extruder tube. This cutter will cut the tube to the exact 45mm. Simply insert 4mm OD tube into the cutter until it just pokes out the other end. Then,...

... the different sides, mirror this file in the slicer. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2-0.3mm Infill: 35% Filament: Hatchbox PLA Notes: It also works in ABS Category: 3D Printer Parts

Soporte de bobinas para FlashForge Creator Pro. Se imprime la base para posteriormente añadir la sujeción de bobinas que trae de fábrica la Creality Ender 3 y sus derivados. ... Se requiere 2 tuercas M5, los tornillos se pueden usar los mismos que...

<p>Just wanted to share my dummy of the FFCP printhead for all you modders out there. ...The dimensions might not be extremely exact, however it should work well for most modifications. I included a left extruder only variant for single extruder mods.

Holders used to put a thermometer/hygrometer at a easy-to-view place inside the Flashforge Adventurer 3 enclosure:Top holder: Holder viewable from above. Clips on to frame.</li><li><i>Top cable clip</i>: Cable clip that can be used if the...

I printed a new one today using Hatchbox yellow ABS with support material and got very good results (slicing with Simplify3D). This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the...

Printer: Flashforge Dreamer Rafts: Any Supports: Yes Resolution: .2mm Infill: 100% Notes: Minimal supports on this, two small spots where screws sink into the grill face. Recommended to use these; can't hurt anything and the screws hide ugliness. Be...

Hi There, The main wire set, which I've dubbed the Umbilical Cord on my FlashForge Creator Pro, has taken to bending itself to one side and now relentlessly rubs against the plexiglass top. This irritation prompted me to design a straightforward...

FlashForge Dreamer Print Bed Spring Replacement Guide Replacing the print bed spring on your FlashForge Dreamer 3D printer is a straightforward process that requires minimal tools and expertise. Begin by unplugging the power cord from the printer to...

... The 120mm fan to dryer duct adapter used in the picture can be found here: http://www.thingiverse.com/thing:1163183 Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 is fine Infill: 20% Notes: A simple print.

Human: FlashForge Finder Side Mount 1kg+ Spool Holder Increase your print capacity with my side mounted spool holder, allowing you to have three spools sitting on your machine at one time. Key Features: * Ambidextrous design for mounting on either...

Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.4 Infill: 20% Notes: Use less infill for more elasticity. I used a 0.4 layer height, but anything really doesn't matter. How I Designed This Build-plate leveling I...

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

For this mod you need to use the Bumper mount remix -Wheel Shafts M4 Remix Use this mod to convert the front and rear axles to M4 studs instead of M3 screws. ...You'll need M4 threaded Rods cut to length for the rear and 2x 25mm screws for the front ...

Attach the mag-clips to the bed using the 3mm bolt and nuts from the original Flashforge build plate with enclosed printed washers. The mag-clip heights are set just below the removable bed plate height to allow nozzle clearance of your print head. I...

The X Axis Carriage For Dreamer 3D Printers Offers Enhanced Reliability and Strength Replacing The Standard X-Axis Carriage On FlashForge Dreamer Units, This Custom Design Ensures Continuous Functionality Even In Extreme Printing Conditions. Note...

... part modelling tools like basic 2D/3D sketching, Circular Pattern, Filet etc. Very first we will create surface features and later convert them to the solid body, in other words, what we can say, Autodesk Inventor surface to solid body techniques.

... **Print Settings** * **Printer:** Flashforge Dreamer * **Rafts:** Not required * **Supports:** Not necessary * **Resolution:** Set at 200 for optimal results * **Infill:** Use a density of 10-20% for balanced performance **Important Notes:**

This customizable guide is specifically designed to secure Flashforge Creator Pro filament tubes. It elevates tube ends away from printer casing, preventing entanglements and optimally positioning them within the superior Makerbot acrylic dome found...