flashforge logo 3d models

I printed a new one today using Hatchbox yellow ABS with support material and got very good results (slicing with Simplify3D). This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the...

Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.4 Infill: 20% Notes: Use less infill for more elasticity. I used a 0.4 layer height, but anything really doesn't matter. How I Designed This Build-plate leveling I...

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

... The 120mm fan to dryer duct adapter used in the picture can be found here: http://www.thingiverse.com/thing:1163183 Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 is fine Infill: 20% Notes: A simple print.

The X Axis Carriage For Dreamer 3D Printers Offers Enhanced Reliability and Strength Replacing The Standard X-Axis Carriage On FlashForge Dreamer Units, This Custom Design Ensures Continuous Functionality Even In Extreme Printing Conditions. Note...

Attach the mag-clips to the bed using the 3mm bolt and nuts from the original Flashforge build plate with enclosed printed washers. The mag-clip heights are set just below the removable bed plate height to allow nozzle clearance of your print head. I...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 15-20% Notes: I strongly recommend printing the pieces at .2 resolution to ensure accurate results. My own prints came out perfectly, with no need for...

Adapter system for FlashForge Inventor This adapter system is designed to allow a FlashForge Inventor to handle reels from other manufacturers. Currently supported are: * FlashForge original 600g reels (180mm diameter) * eSun 1kg reels (200mm...

This is a spool holder for the Flashforge Adenturer 5M because the spool holder it comes with it awful and doesn't even keep the spool from sliding off.UPDATE: I redesigned the spool holder to be longer and a bit sturdier. Because of the way the...

... This holder is customizable for Flashforge Creator Pro filament guide tubes, keeping their ends at a safe distance from the printer case to prevent entanglement and positioning them at an angle that complements the superior Makerbot acrylic dome.

This accessory securely attaches to the side of a FlashForge Creator X by snapping into the built-in carriage mounts on either side. A hex wrench storage section fits exactly 3 standard 1/4" drive wrenches typically supplied with the 3D printer...

GoPro Mount for Flashforge Creator Pro. Two arm lengths are available, 45mm and 60mm. This mount will hang from the front of the printer, with a hump in the middle to fit over the screw. (This is designed specifically for those who paid $1,200;...

I bought a Flashforge creative pro 3D printer in 2017 to handle filament more efficiently. Different diameter spools can be secured with the rear-facing filament holder on this printer. The filament alignment bridge helps prevent knots from...

I decided it was time to upgrade my FlashForge Finder to a heated bed. There were a couple tutorials that I found for the project, but they used a fabricated part and I did not have the material or tools. So I designed this adapter to replace the...

... **Print Settings** * **Printer:** Flashforge Dreamer * **Rafts:** Not required * **Supports:** Not necessary * **Resolution:** Set at 200 for optimal results * **Infill:** Use a density of 10-20% for balanced performance **Important Notes:**

**Updated External Spool Holder Now Available** Now featuring two versions to accommodate both 3 and 4-slot models of the FlashForge Adventurer 3, this external spool holder enables the use of third-party filaments with ease. This innovative holder...

To improve the performance of a FlashForge Creator Dual (Replicator 1 Dual) printer, I designed this bracket. It holds higher quality ceramic bearings (5mmx10mmx4mm) in place within the case for Y-axis motion transfer rods. The flangeless bearings...

Although I'm extremely pleased with my Flashforge Dreamer, a persistent problem has been the way the cable harness to the heated head drapes down onto the rubber belt in specific positions, which had me decide to design a swinging arm that would...

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

External Spool Holder for Flashforge Dreamer. Replace the left door with this holder. Attach a Teflon tube (4mm outer diameter) to ease filament flow into the build chamber. Using the tube significantly reduces friction, but it's not necessary - you...

Holders for common cheap thermometers and hygrometers for the Flashforge Adventurer 3: - _Top holder_: Holder viewable from above. Clips on to frame. - _Top cable clip_: Cable clip that can be used if the thermometer/hygrometer has a cable. -...

This print is a single layer test print designed to surface levelling issues on your Flashforge Adventurer 4. The design is 220mm x 200mm to fit the entire printable area of the ADV4.The ADV4 has a 9-point bed levelling system that does not provide...

ServiceTray for FlashForge Creator Pro 2016 fits perfectly into the top hole on this machine, making maintenance of the extruder, fans and nozzles much simpler. This useful accessory is designed to be printed as a single piece, but an alternative...

(see here a related thing: http://www.thingiverse.com/thing:1200876 ) This customizable add-on funnel improves the interface between the Flashforge extruder and the filament guide tubes, and helps keeping the guides in place, especially for the...

I recently acquired an old FlashForge Creator (with the wooden frame), but it was missing some parts - including one of the filament feeder tubes.  I'm not sure what the original ones were made out of, but I had some PTFE tube and fittings on hand...

If some of your filaments have larger inner tubes than what the FlashForge Creator can handle with its current spool posts, they should be placed on the back of one side of the spool posts. Users with dual extrusion models will need to print two of...

(Note, first picture is the original design, in the second you can see I made the clips 3mm thinner) This is a revision to my ELP camera holder that just slides right onto the back "flashforge" plate. I had issues with the extruder rubbing against my...

@3DPrintFresno Certain filaments come with a bigger interior tube than the FlashForge Creator's current filament spool holders, so these fit onto the back of one side of the Creator's filament holders. If you have a dual extrusion model, you will...

This becomes even more essential when printing ASA/ABS etc to cut down on the amount of fumes getting out.As the rear panel of the Guider II is metal the blanking pieces make use of 5.5mm square x 2.5mm high magnets.There will be another part to...

This clip-on filament feeder is tailored to fit seamlessly onto the side of a FlashForge Finder printer. Clipped snugly to the right side, where the horizontal motor hums along, this design ensures sufficient clearance for the motor's passage without...