flashlight flashlight 3d models
5716 3d models found related to flashlight flashlight.
cults3d
Flashlight holder - flashlight stand Screws 1/8" x 3/4" Handle diameter 22,2 mm Flashlight diameter 25mm 1/8" x 3/4" screws Handlebar diameter 22.2 mm Flashlight diameter 25mm
cults3d
ENGLISH Flashlight case that can receive a 1.115'' (28.32MM) diameter sleeve English Flashlight case that can accommodate a sleeve with a diameter of 1.115'' (28.32MM)
grabcad
Туба для фонарика Фонарик Xhp 70.2 Aliexpress. ...Tuba for flashlight Flashlight Xhp 70.2 Aliexpress
thingiverse
Customized version of https://www.thingiverse.com/thing:109521 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=109521
thingiverse
Remixed https://www.thingiverse.com/thing:737919 to fit a 25mm to 28mm flashlight also added a Picatinny rail hole for a blot and nut to fit it into place
prusaprinters
Quick functional print to make sure I always know where my flashlight is when I need to get into my shed at night. PLA is fine for material, prints with no supports. ...Mounts with a #8 wood screw.</p>
thingiverse
This is where I wanted it, here was a test fit of just the flashlight:  Here it is...
thingiverse
It turns out the flashlight I got (an NRA gimme flashlight) was too small to fit in the clips. This is a bushing to adapt a small diameter flashlight to the desk stand. Instructions For Rev A...
thingiverse
The flashlight I used has a 29mm diameter, so standard 1-inch (25.4mm) scope rings would not work. 3D-printing to the rescue! In case anyone wants to modify the design for their own lights, I have included the STEP file. I have never used STEP...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9eMtQXzQg3Y
thingiverse
Height: 15.3 cm Diameter flashlight: 4.05 cm See caiofelipetzs make for a different approach. Instructions Print it with light colored plastic (like orange pla), make sure the walls are thick enough...
thingiverse
Customized version of http://www.thingiverse.com/thing:133212 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=133212 Instructions Using the following options:...
thingiverse
M-lok flashlight mount for ArmyTek Prime C2 and others with the flashlight body 19-22mm. Suposingly could be printed without supports, but I did not risk. 0.2mm layer height and 4 walls will provide the optimum strength for this item This is a...
thingiverse
... to the switch end after it's dried. Step 5: Attach front end of printed flashlight to midsection, theres a lot of play, sorry! I'll revise this when I have time. Step 6: Attach rear end of printed flashlight to midsection. ...Step 7: Luigi it up.
cults3d
Flashlight holder ideal for nighttime practice. ... Tested on the battlefield Tactical Flashlight 26-29mm diameter Rail taken from Cronus Tactical
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dL0mfBLjXDY
thingiverse
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options:...
thingiverse
It hangs on a strap, waistband, belt, etc and holds the flashlight a bit loosely so you can reposition it. ... I included the OpenSCAD file I used to design it with some variables for customization, like frame thickness, clip length, sturdiness of...
thingiverse
I've noticed there is a shortage of real, good diffusers for flashlights. I like to use my lights as lanterns and area lights when I camp or use them at work, so I used my knowledge of photographic and acoustic diffusers to create a "lantern" add-on...
thingiverse
Customized version of http://www.thingiverse.com/thing:250899 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=250899 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:133212 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=133212
thingiverse
16 gauge under-mount quick release for j5 tactical flashlight
thingiverse
Customized version of http://www.thingiverse.com/thing:494174 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=494174 Instructions Using the following options: barrel...
thingiverse
Quickly accessable, but rigid mount for those generic Wish/Aliexpress/eBay led torches. Piece in the middle is optional and prevents movement back and forth in horizontal installation. ...2 screwholes under rings.
thingiverse
Customized version of http://www.thingiverse.com/thing:494174 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=494174 Instructions Using the following options:...