flexrc 3d models

FlexRC Ascent motor guards Print in TPU

Protective sleeve for electronics of FlexRC Pico X FlexRC Pico X frame:https://flexrc.com/product/pico-x-frame/ Nylon sleeve for Pico X:https://flexrc.com/product/sleeve-for-flexrc-pico-core/

Canopy with mini buzzer mount and hole for the VTX antenna for the ultralight FlexRC Ninja and FlexRC Ninja BAT frames that support 16x16, 20x20 and whoop sized electronics as well as 11xx (4 holes) and 08xx (3 holes) motors. ... FlexRC Ninja frames are...

Arms guards for FlexRC Ninja FPV drone frame that help to reduce carbon fiber delamination in case of the front crash as well as add extra protection for the motors

... possibility to mount T-Immortal Antenna to the side as well as from inside of the canopy. You can also purchase the following canopies: - Canopy for GPS and SMA antenna - Canopy for DJI Air Unit - Canopy for SMA antenna - Canopy for Caddx Vista

This canopy is designed for FlexRC Slim 2.5" - FPV Quadcopter Frame and features mount for the buzzer, rear hole for FPV antenna and easy access to USB and two antenna holes. ... Best results when printed with TPU kind of material.

Specifically designed for FlexRC Frog FPV quadcopter frame, this bumper extends and protects frame and bigger micro FPV camera in case of impact. It also adjusts height of the standoffs when combine with 30.5x30.5 to 20x20 adapter. ... We've got best...

... get virtually indestructible canopy. cut outs for motor wires and battery power cable cut out for the camera cut out for FPV antenna Links to the frame: Frame: https://flexrc.com/product/frog-frame/ DIY Kit: https://flexrc.com/product/frog-diy-kit/

Small Landing stand for FlexRC OWL The hole is for M3 screw Print Settings Infill: 0% Notes: Print it with 0% infill 2 layer for Perimeter and 3 layer for top/bottom Using flexible material ex. ...TPU, TPE or Filaflex

VTX mount for FlexRC ascent quadcopter. I have only printed the IGES file. The STL has a weird thing on the end,.... not sure if it will appear in the print. I drilled a hole for the receiver antenna.... ...(you may have a diversity and need two holes

FlexRC Pico Owl V2 ducts.

Little carrying case for the delicate FlexRC Nano-X

TPU decorative and protective border for the top carbon fibre piece of FlexRC Colugo Frame

Buzzer mount for FlexRC Colugo frame that allows it to be installed on any of the available M3 standoffs.

TPU decorative and protective border for the front carbon fibre piece of FlexRC Colugo frame

TPU decorative and protective border for the bottom carbon fibre piece of FlexRC Colugo frame

Flexible TPU mount for VM275T camera onto the FlexRC Nano-X (16mm stack)

Flexible camera mount has stretchable hooks which securely hold CM275t FPV camera in place. ... It will work with the following frames: FlexRC Mira 65 FlexRC Mira 84 FlexRC Nano X It CM275t mount can can also be purchased here

Flexible TPU mount for VM275T camera onto the FlexRC Nano-X (16mm stack) Category: R/C Vehicles

GoPro Session Mount for FlexRC Colugo Freestyle / Proximity frame that can be used with dual 20x20 stack or single 30.5x30.5 stack of any height as well as 3-4" replaceable arms and optional Bumper configuration.

These landing feet are for FlexRC Mini Owl:https://flexrc.com/product/mini-owl-frame/ and Mini Owl Piko Edition:https://flexrc.com/product/mini-owl-piko-edition-frame/ In addition to extra protection from landing impact it also provides additional...

Not a problem, It can be purchased here:https://flexrc.com/product/nail-clipper-propeller-cutter/ It works great for awesome RotorX RX2535 props:https://flexrc.com/product/rotorx-rx2535w-props-8-cw-8-ccw/ and generates great results for FlexRC drones...

FlexRC Owl front skirt can replace front 25mm standoffs and help to prevent damage to propellers when flying through bushes. ...More information can be found here: http://www.rcgroups.com/forums/showthread.php?t=2631117

... skirt which help to have all wires nicely hidden. ...It replaces Flight controller 25mm standoffs and works well with FlexRC Owl quadcopters. ...For more information about Owl please visit: http://www.rcgroups.com/forums/showthread.php?t=2613776

Single wall sleve with a lip to duct the props on a FlexRC Owl 3" frame. Use a 4 outline skirt with 0 offset to create the lip, and print in vase mode. ... Roughly 3.5G each when printed with PLA.

Little carrying case for the delicate FlexRC Nano-X Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: 15% Category: R/C Vehicles

After "loosing" my FlexRC Ascent in tall grass several times (once took 45 minutes to find) I decided to try a Loc8tor. A gent at my RC club had them on his plane and said they do work. So I designed a top mount for the Ascent. It sort of looks like...

Air Unit Mount for FlexRC Flying Fox

Camera mount for Mini and AIO cameras like: - CM275 / VM275 - DIATONE 600TVL Miniature Camera for FlexRC Ascent 2" FPV Racing Drone and FlexRC Lora 2.5" FPV Racing Drone

FlexRC Ninja FPV drone frame canopy that hold Caddx Vista antenna