flight stand 3d models
165952 3d models found related to flight stand.thingiverse
This is just a simple inceptor flight stand I modeled back with the previous inception release but never uploaded. ... You will probably need to warm it up with hot water to bend it into place or us the split pieces.
thingiverse
I needed a flight stand for a model in a miniatures wargame, and didn't feel like a boring smooth pillar. ... Printed on a Photon with no supports.
thingiverse
A modular flight stand for tabletop rpgs. It's scaled to a 1 inch grid (or about 25mm). ... Make your minis fly!
cults3d
I needed a flight stand for a model in a miniatures wargame, and didn't feel like a boring smooth pillar. ... Printed on a Photon with no supports.
thingiverse
This is a flight stand for small fighter squadrons. It is intended to be universal and system agnostic but its was created for Rogue Trader. ... Feel free to improve or change the design as you wish.
cults3d
This model was designed out of necessity for simple yet sturdy and easy to print combined flight stand and base for 40 K type flying models Hope you enjoy.
thingiverse
Seriously, a Falcon flight stand is going to snap at the vehicle underbelly if you accelerate too hard. Use at own risk. I have included the single latch as an easy starting point for remixes. The angle isn't 100% in line with the curvature of...
thingiverse
Twilight Imperium 3rd ed Flight Stand. Made ready to print and fits well on the hexes so you can raise up those Space units and fit more on a hex. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9NvFFL90nN6
cults3d
Collection of flight stand bases I designed to replace the ones I keep breaking! Contains the following base sizes / heights: 25mm Base 30mm, 40mm and 50mm height. 32mm Base 30mm, 40mm and 50mm height. ... 60mm Base 25mm, 30mm, 40mm and 50mm...
thingiverse
Collection of flight stand bases I designed to replace the ones I keep breaking! Contains the following base sizes / heights: 25mm Base --- 30mm, 40mm and 50mm height. 32mm Base --- 30mm, 40mm and 50mm height. 60mm Base --- ...
thingiverse
This flight stand incorporates a wide base, hefty fillet, and the stem is reinforced with a nail. The idea is that you put a magnet into the bottom of the model stand stick to the head of the nail at the top of the stem. Use the TinkerCAD link...
thingiverse
My flight stands for Dungeons and Dragons, made to fit 1 inch bases, both square and round. The dials are left free spinning so that you can adjust it to indicate height of 5ft up to 60ft in game. There is a plain base included in case you want to...
thingiverse
The modular flight stand is made up of a base and additional sections each 1″ in height and width giving your creatures flight as high as your imagination (or available filament) while staying within your battle mat grid. Print the base and as...
thingiverse
This is my rendition of a flight stand. There's 3 different size posts included, tolerances are tight so depending on how you print them and with what resin they SHOULD go together easily. Dry fit the pieces first, if they don't go together easily...
cults3d
Thus the idea for this flight stand was born! It's a pretty simple setup, built on top of (and hence compatible with) the CyberBase System. The main base piece is designed with a series of holes around and in the middle of it, where 5mm hexagonal...
thingiverse
Stacking flight stand for 25mm miniatures for Dungeons and Dragons. ...I have not printed this yet so hopefully it works.
thingiverse
This model is the belly section of SebTheis's Helldrake modified to allow mounting to a flight stand. ...As a side effect of me modeling the cut in the belly for the flight stand, the polygon count of the model has also been reduced a bit.
cults3d
Need some flight stands for your flying infantry like Suppressors or Pteraxii? Well, look no further! I modeled this stand to match the approximate height of the original GW stands. ...Works great printed in clear resin or any other color.
thingiverse
these are unnecessary but can be used for my Flight Stands at https://www.thingiverse.com/thing:4105083 these are designed to make the top of the stands exactly on an inch incrament. ...
thingiverse
Created a simple flight stand in meshmixer. Comes in two parts which stick together. I'm probably going to expand on this by making taller versions, but time will tell. ... 75 mm square on top/bottom.
thingiverse
This is a replacement flight stand for Wings of Glory figures by Ares Games. Use 3mm carbon fiber rods inserted into the base, with the ball and socket joint at the top of the base. ... (I use 3mm rods of 10cm, 20cm, 30cm and 40cm length to reflect the...
thingiverse
This is a flight stand for small-sized (i.e. 20mm diameter) heroic scale miniatures. The main support column is 2mm diameter, and I added a small 1mm diameter section on top for gluing on a very small miniature (e.g. flameskull). ...This can be cut or...
thingiverse
Flight stand for all 40k flyers. Designed this so that I could hold my crimson hunter while airbrushing as I didn't want to get paint on the clear acrylic stand. Has a hole in the bottom for a small fidget spinner bearing, or can be blue-tacked...
thingiverse
I needed to replace some aging flight stands I had printed out a few years ago, so I made these simple ones to print without standoffs on my resin printer. ... I may alter the design in the future to make these stackable or add a coupler for stacking,...
myminifactory
This flight stand for wargaming makes it easy to test line of sight at the specified 6" flying height, AND doubles as a convenient handle for moving your flyers around the tabletop without bumping tall buildings or other terrain. Photo shows a...
thingiverse
Thank you!** DESCRIPTION A replacement part for the large vehicle flight stands such as the AAT, Saber Tank, and Airspeeder. <h3>FILE DESIGN & DETAILS</h3> <ul> <li>Test printed to ensure a good fit with the official models. </li> <li>It is...
thingiverse
Thank you!** DESCRIPTION A replacement part for the commonly missing Imperial Speeder Bike flight stand. <h3>FILE DESIGN & DETAILS</h3> <ul> <li>Dimensioned using the actual part for reference. </li> <li>It is manifold and has been checked for...
thingiverse
Flight stands suitable for Team Yankee or Flames of War Peg fits a 5mm wide magnet. ... Two stands, short and tall
thingiverse
... the other has a more "scooped" top and is shorter. Place your favorite airborne toys on one of these bases to give them the appearance of flight (kind of). I've been printing mine in a translucent PLA. Resize as you see fit. ...Requires supports.