flitetest 3d models
477 3d models found related to flitetest.thingiverse
FliteTest firewall for power pods. ...I use it on my spitfire and works great.
thingiverse
FliteTest Swappable firewall reinforced Updated: 2014-08-23
thingiverse
Flitetest FT Simple Firewall for FT Versa Wing Inspired by http://flitetest.com/articles/ft-versa-wing-build
thingiverse
Engine support for FliteTest Versa Wing For engine diameter 35mm (EMax Gt2812/06 ) Weight 14g
thingiverse
I designed this for my FliteTest screw drivers that come with the Power Packs.
thingiverse
Designed specifically for Flitetest screwdrivers. ...It holds them in place very well and is super stable
thingiverse
Canopy for Flitetest Mig-3. ... Print in vase mode and trim edges with scissors for fit
thingiverse
For the FliteTest ElectroHub Multirotor series.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys Instructions Printed on a PrintrBot Simple Metal. Using Simplify3D slicer. ...PLA material at .2 layers MakerGeek 1.75 PLA Printed...
thingiverse
Rate tool for the FliteTest Tiny Trainer. The only measurement i could find for angle on the plans was 16*. ... If i had to guess low rates are between 3 and 7 degrees less.
thingiverse
This uses the FT Versa power pack from Altitude Hobbies. ...http://www.altitudehobbies.com/flitetest-combo-flight-packs The motor uses a standard 16mm x 19mm bolt hole pattern.
thingiverse
This setup for the FliteTest Versa Wing it is not created te use with a 2200KV engine (340Watt) and a 3S2200MHa lipo battery but it flies very well. The engine (2200Kv) is much too strong which makes it very nice. Use the higher elevator horns and...
thingiverse
Rails: 3/8" Poplar Dowel.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys Instructions Printed on a PrintrBot Simple Metal. Using Simplify3D slicer. PLA material at .2 layers MakerGeek 1.75 PLA "Racy Red (Transparent)" Printed...
thingiverse
Thought I'd recreate the flitetest.com control horns that the guys use on their foamboard models. These can be used to control the flight surfaces on your model aeroplane such as ailerons, elevator, rudder, flaps, elevons etc. ... I plan on using these...
thingiverse
Simple fire wall for larger power pods from Flitetest. The bolt pattern works for the couple motors I had on hand. You may need to drill or modify the part as needed for other motor bolt patterns. An ridge was added for strength and more surface...
thingiverse
Links: * Purchase 5-pack from flitetest: https://store.flitetest.com/flite-test-ez-chuck-gliders-5-pack-flt-1064/p873723 * Build video: https://www.youtube.com/watch?v=CCARMDn7yjM Be sure to cut in the following order: * Blue - Words/Writing * Green...
thingiverse
This is the newest firewall that Flitetest has released with the FT Explore. The tolerances are a little tight and may need a slight bit of sanding depending on print quality. When assembled I just used some medium CA glue and kicker, and looks very...
thingiverse
This is my version of flitetest's HQuad. The postage ruled out a purchase as it pushes the price up too far for me in the uk and its only a wooden kit so i decided to make one and make it available for all over this side of the pond. If anyone wants...
thingiverse
This is my power pod motor mount for the Flitetest power pods in an attempt to create a slightly more aerodynamic mount for smaller motors and propellers. Fits 16mm by 19mm motors. Should be able to print without supports on 0.2 mm extrusion. ... I...
thingiverse
Swappable firewall for FliteTest C Power Packs. Works with P-40, Mustang, Spitfire, etc. 51 mm x 43 mm x 2.4 mm 16x19 mount. 0.2 mm layer height with 8 walls and 6 top/6 bottom layers to make solid. Could probably be printed fine with...
thingiverse
A firewall for FliteTest's Mini series tractor planes (mini scout, mini mustang, etc). Not that the through-holes for the BBQ skewers used to hold the mount to the model body DO NOT MATCH all the FT models. Print the mount and use IT to gauge...
thingiverse
This is a FPV backpack for the the flitetest Arrow flying wing. It is designed to protect your camera by moving the camera further back on the wing. It also makes your fpv setup modular so you can move it within wings. It has many slots and holes to...
thingiverse
https://store.flitetest.com/flite-test-ft-a10-warthog-electric-airplane-kit-1537mm-flt-1063/p873722 The FT A-10 supports the Power Pack "C" Dual Motor electronics bundle:...
thingiverse
An improved firewall for the standard size Flitetest power pod (for Spitfire, Mustang, Simple Cub, Corsair, etc). I have included motor mount holes (1.2mm diameter, 34mm PCD). There is a hole at the bottom to feed your XT60 connector from the ESC...
thingiverse
I recommend using a wood (laser-cut 1/8" plywood) firewall so the motor's heat does not melt and deform your firewall, but I designed a standard FliteTest firewall model if you're in a pinch. ... All my airplanes have one of these quick-mounts on it,...
thingiverse
This is a fuselage, firewall replacement for the Flitetest Tiny Trainer. The nose of the plane is two inches shorter but plenty of room for batteries. I have flown this and had very good success. Parts should be CA glued together. The hatch has a...
thingiverse
They also have a scratch build video for the Tricopter and here is the link:- http://flitetest.com/articles/tricopter-scratch-build. I thought others here would like the parts too so here they are. PS I have just added the Wheel arms you will need...