flitetest.com 3d models
1735079 3d models found related to flitetest.com.thingiverse
Thought I'd recreate the flitetest.com control horns that the guys use on their foamboard models. These can be used to control the flight surfaces on your model aeroplane such as ailerons, elevator, rudder, flaps, elevons etc. ... I plan on using these...
thingiverse
These are the Flite Test Mini control horns as used on the Mighty Mini Corsair and Mustang. ...If you liked my design and want to show your appreciation, why not leave a small donation of a £/$/€ or two through the blue TIP BUTTON on the left.
thingiverse
Flitetest FT Simple Firewall for FT Versa Wing Inspired by http://flitetest.com/articles/ft-versa-wing-build
thingiverse
This is the control horn for the Flitetest mini airplanes.http://store.flitetest.com/aircraft-accessories/
prusaprinters
This is the control horn for the Flitetest mini airplanes. ... http://store.flitetest.com/aircraft-accessories/ Category: Hobby
grabcad
FT Radial 2218B 1180kV Brushless Motorhttps://store.flitetest.com/ft-radial-2218b-1180kv-brushless-motor/
thingiverse
This is a motor mount to fit the flitetest.com FT Sparrow
thingiverse
For the FliteTest ElectroHub Multirotor series.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys Instructions Printed on a PrintrBot Simple Metal. Using Simplify3D slicer. ...PLA material at .2 layers MakerGeek 1.75 PLA Printed...
thingiverse
... is much too strong which makes it very nice. Use the higher elevator horns and make the travel of the elevator not more than 20mm up and 20mm down. More information about the plane:http://store.flitetest.com/ft-versa-wing-speed-build-kit/
thingiverse
Rails: 3/8" Poplar Dowel.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys Instructions Printed on a PrintrBot Simple Metal. Using Simplify3D slicer. PLA material at .2 layers MakerGeek 1.75 PLA "Racy Red (Transparent)" Printed...
thingiverse
https://store.flitetest.com/flite-test-ft-a10-warthog-electric-airplane-kit-1537mm-flt-1063/p873722 The FT A-10 supports the Power Pack "C" Dual Motor electronics bundle:...
thingiverse
Links: * Purchase 5-pack from flitetest: https://store.flitetest.com/flite-test-ez-chuck-gliders-5-pack-flt-1064/p873723 * Build video: https://www.youtube.com/watch?v=CCARMDn7yjM Be sure to cut in the following order: * Blue - Words/Writing * Green...
thingiverse
Check out my write up over at http://backyardrc.wordpress.com/2013/08/25/biplane-motor-mount/ For detailed build instructions check out flitetest's site:http://www.flitetest.com/articles/baby-blender-2-draft The baby blender is small biplane in the...
thingiverse
They also have a scratch build video for the Tricopter and here is the link:- http://flitetest.com/articles/tricopter-scratch-build. I thought others here would like the parts too so here they are. PS I have just added the Wheel arms you will need...
thingiverse
This mount holds the KK2 family of flight controllers from HobbyKing. ...The mounting points are placed so to line up with the prexisting holes in the BatBone frame from www.flitetest.com.
youmagine
I bent the steel wire for the landing gear for my FliteTest.com FT-Storch, only to find that I suck at bending it to spec, so the plane would've been rolling down the runway kinda lopsided. Not good, and even worse at speed trying to land it! So,...
thingiverse
... single-centered and 2-skewer setups (check the pictures of my prototypes). I have to thank www.flitetest.com for starting my interest - it's a truly great team of people, all of them very inspiring. ...Support FliteTest and have a nice flight :)
thingiverse
See http://flitetest.com/articles/ft-mini-scout-build-mighty-minis for build instructions of the model for which this was designed. Instructions The walls on this are intentionally very thin. I...
thingiverse
The article was written by a user called winglet and can be found here: https://www.flitetest.com/articles/sea-duck-school As it stands the user said he did not have the stl's to upload so I created my own with a few modifications. This is only a...
thingiverse
From the FT-Racer/Slinger:http://www.flitetest.com/articles/ft-slinger To P51'shttp://www.flitetest.com/articles/p-51-swappable-with-plans And Spitfireshttp://www.flitetest.com/articles/ft-spitfire So we decided to design a set of 3D printed motor...
thingiverse
FliteTest firewall for power pods. ...I use it on my spitfire and works great.
thingiverse
Checkout my full post over at BackyardRC.workpress.com:http://backyardrc.wordpress.com/2013/09/03/flitetest-baby-blender-with-3d-printed-landing-gear and FliteTest's site for build instructions: http://www.flitetest.com/articles/baby-blender-2-draft...
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Simple mount, just print and use. ...Note: This is for the 3/8" wider pod by dayve ( http://forum.flitetest.com/showthread.php?24402-FT-Mini-Arrow/page9 ) when cutting your wing, leave 3/16" on each side and it will fit perfect. ...Have Fun!
thingiverse
Want a refund for 2 hours on my life :( ) I recently got the Flitetest Spitfire https://store.flitetest.com/ft-spitfire-speed-build-kit/ and am loving it but I'm missing something from my build.... retractable landing gear. Now it's near...
thingiverse
This uses the FT Versa power pack from Altitude Hobbies. ...http://www.altitudehobbies.com/flitetest-combo-flight-packs The motor uses a standard 16mm x 19mm bolt hole pattern.