float x spacer 3d models

This is a 3/32" tile spacer, and I was unable to locate one of this size in local stores. The cost is approximately $0.01 each, and it takes around 45 minutes to print 25 pieces. A360 files are available here: https://a360.co/2T45Kxg I made these...

Keeping wires neatly organized is a breeze with this ultra-simple cable spacer, held in place by just two tiny zip ties. Print Settings Printer: Choose the Velleman k8200 for this project. Rafts: No raft needed for this print. Supports: No supports...

... To keep the screw heads from scratching your desk, insert a spacer between each spool and at the bottom. These prints are straightforward; ensure that the flat side faces the print bed when printing. ...Use a 608 bearing to complete the project.

  A simple spacer for the BEKVÄM spice rack from IKEA so you can stack multiple with enough clearance for spices etc. inbetween. Prints without support if you rotate it with the bottom part on the build plate (like in the attached Cura screenshot).

A custom spacer mounts the Cyclops TX1769 alongside an Akasa AK-189BK-28 fan seamlessly. Any 25 mm fan brand should fit perfectly in this setup. The VTX is secured with tiny self-tapping screws, while the fan uses M3 screws. The printed threads work...

To circumvent drilling additional holes, which can be quite imprecise, I designed a set of spacers to elevate the board effectively. The outcome was successful, but I took it a step further by incorporating double-sided VHB tape for added...

Spacer for setting the depth of the Matchfit dovetail bit. One side is set slightly shallow for using a 1/4" straight bit to remove the bulk of the waste. Then switch over to the Matchfit dovetail bit at full depth for a nice clean dovetail groove.

The fan and spacer are secured by spring clips, eliminating the need for screws, which would otherwise require holes - instead, they rely on a slight bump to keep things in place.\r\n\r\nMinimal remnants of the original file remain, but I've included...

FORK SPACER 1---------------------------------------------------step1: configure material to titanium step2: sketch circles first according to geometry presented in blue prints step3: make sure you evenly space the circles to 10mm step4: connect...

FORK SPACER 1---------------------------------------------------step1: configure material to titanium step2: sketch circles first according to geometry presented in blue prints step3: make sure you evenly space the circles to 10mm step4: connect...

Thought if I had a spacer I could just lay the bag flat on something hard and that would work to back up the pump, but let the air escape from the bag, it might work with just my hands. Created this little spacer in Openscad (file included). The...

If I were to create this model again, I would have not rushed it.Fork Spacer 1:Mass = 8539.75 gramsVolume = 1856467.67 cubic millimeters area = 132767.78 square millimetersFork Spacer 2:Mass = 5925.14 gramsVolume = 1288074.28 cubic millimetersSurface...

This is a spacer used to separate a joycon from a Nintendo Switch, allowing the joycon to still be mechanically attached but not directly connected to the system. By default the Switch doesn't allow you to play with one joycon attached and one...

Rather than run to the store I made some spacers for the smaller sized dowel rod. This is also the first thing I have ever designed, and I realize it isn't horribly impressive but its a big step for me. ...Print instructionsPLA or PETG 20% infill or...

This is a trampoline spacer, used to hold the net support arms to the frame. I built this model to print after a wind storm damaged our trampoline. Ours was purchased from Sam's Club. Print Settings Printer Brand: LulzBot Printer: TAZ 5Rafts: No...

A friend had to split two Wi-Fi units that were stacked on top of each other, which were overheating badly, a simple set of four 10mm thick spacers keeps them cool. Customized version of http://www.thingiverse.com/thing:1657791 Created with...

This is a simple spacer to go behind ringed curtain tops to get correct spacing when Curtains are open. This is a thing my wife asked me to make, and the results were pretty good. I have included pictures of the Curtains in question, also a STEP...

Rather than run to the store I made some spacers for the smaller sized dowel rod. This is also the first thing I have ever designed, and I realize it isn't horribly impressive but its a big step for me. ...Print instructionsPLA or PETG 20% infill or...

Designed a mask spacer for 3d printing. It keeps the fabric of the mask from touching your mouth which bothers some people and makes mask wearing uncomfortable. Also increases breathability by increasing fabric surface area for air to flow through. I...

This is a simple spacer to go behind ringed curtain tops to get correct spacing when Curtains are open. This is a thing my wife asked me to make, and the results were pretty good. I have included pictures of the Curtains in question. I made this...

... due to filament entanglement. To prevent these issues, I suggest installing the spacer first, then loading the filament onto the spool as you normally would. ...Once in place, remove the ties and securely tighten both halves of the spool together.

This asthma spacer features a three-dimensionally printed part made from FDM material, combined with a circular tube measuring two inches in inner diameter and adjustable length. The design allows for disassembly and easy cleaning. Printing time on...

These spacers ensure adequate spacing between hangers. They are easy to attach and detach. They are designed for a 1.5mm diameter wire clothesline. ... You can view and export the design [here, using...

I could not find a good way to mount the tower with the funnel at the bottom so I combined the 120mm spacer and funnel. This will allow the use of the funnel with any of the available mounts affixed to an open stand. On this modification to my...

I designed this spacer to give more surface for the filter do it's work. It was designed from the print funnel of the original creater... Hint: You can scale for other funnels. And you can also use a second one to push the filter into shape. ...

To create the fork spacer(s), it was split into three parts. First part included just the sketch of the part, which was made by using circles and lines tangent to the circles. For the second part, the part was cut inwards for the top circular...

This is a simple model of the Grendizer-Spacer, available in two versions - one original and the other with added support features that I utilized for my 3D printing project. Print Settings: Printer Brand: RepRap Printer Model: Hephestos Prusa I3 ...

Spacer sleeve company Dremec offers various sizes of Female to Female Standoff in brass and steel materials. ...Models include TFF-M2x5/DR111, TFF-M2x6/DR111, TFF-M2x8/DR111, TFF-M2x10/DR111, TFF-M2x12/DR111, TFF-M2x15/DR111, TFF-M2x18/DR111,...

A simple spacer for the [BEKVÄM spice rack from IKEA](https://www.ikea.com/us/en/p/bekvaem-spice-rack-birch-40070185/) so you can stack multiple with enough clearance for spices etc. inbetween. Prints without support if you rotate it with the...

The tooling insert is 2.5mm deep x 6mm diameter for creating a human-sized 1/8" (3.175mm) deep by 9/64" (3.54mm) wide hole in metal using a 17mm x 7.5mm hole bush.