floppy disk box 3d models

..a keyboard box ✻here✻ ..a floppy disk box ✻there✻

Floppy disk storage box to hold 25 disks.

I created a base and edge connectors for a 3.5" floppy disk box There are files for the bottom; one for disks with one tab and another for disks with two tabs (square holes) in the upper corners. These lock into the base. Edge connectors lock into...

Retro Design Who doesn't know them, the floppy disk box from the 80s and 90s. What was good for floppy disks also works with SD cards. 40 SD cards You can store and even sort all your SD cards in the compact SD Card "Floppy Disk" Box. It holds up...

Storage box for diskettes

... back in the day. This box is designed to contain floppy disks, and is designed with a sliding lid, with a floppy disk design printed on the lid. Ideal for storing floppy disks, or anything if you like having a retro design. ... No supports needed.

Don't throu your old floppy disks reuse them.Snap in strong so no glue required.

Don't throu your old floppy disks reuse them.Snap in strong so no glue required.

No, I did not 3d print the "save" icon!A handy place to keep floppy disks, for those that still use them.

A simple, removable top box to store and transport 5¼" floppy diskettes. Fits about 16, snugly in their jackets. An indent is provided on both sides for labeling. There's no infill or support required, and layer height is up to your preference. ...I...

A simple box for SD cards, shaped like a Floppy Disk Box

Floppy disk boxes, specially for 5 1/4 inch disks, go for 50 bucks on eBay, so yeah, this. Prints fine without supports. Small version that can be printed in small 3D printers like the Ender 3. ...If you want a larger box to fit more disks, let me...

Floppy disk boxes, specially for 5 1/4 inch disks, go for 50 bucks on eBay, so yeah, this. Prints fine without supports. Small version that can be printed in small 3D printers like the Ender 3. ...If you want a larger box to fit more disks, let me know!

Floppy disk boxes, specially for 5 1/4 inch disks, go for 50 bucks on eBay, so yeah, this. Prints fine without supports. Small version that can be printed in small 3D printers like the Ender 3. ...If you want a larger box to fit more disks, let me...

A plain box to hold 3.5" floppy disks. It fits 20 floppies. The walls are 1.2mm thick to work well with a 0.4mm nozzle. Adjust nozzle size in case the slicer doesn't lay three clean lines for the walls and avoid wall separation. An optional cover...

Pen/office organizer consisting of five 3.5" floppy disks serving as the side and middle panels. Same design as referenced thing only with a divider in the middle to help hold a lesser number of pens/pencils. Disks are held in both the top and...

Roughly based on this [tandy disk holder.](https://i.imgur.com/6Jn5T11.jpg) Will hold up to 40 5.25" disks comfortably (4 per slot). ...The lid can be fully folded out to let the box sit elevated for easy access to all the disks (Picture 3).

Revised my original disk box design to allow for displaying the disks right side up. The top contains tabs to click into the square hole in the upper right corner of a disk. These may be a little tight but are intended to catch the disks so that you...

key to open those vintage floppy boxes

key to open those vintage floppy boxes

Only a small thing but many of us have old vintage disk boxes where the pins to the boxes have been lost or broken. This is designed to work in many classic 3.5inch disk boxes with top lids. It will fit most boxes with a 7mm to 8mm hole. ... Best...

Resized version of https://www.thingiverse.com/thing:3097196 to fit 10 3.5'' floppy's.

Resized version of https://www.thingiverse.com/thing:3097196 to fit 10 3'' CF2 disk's.

Box with 20 floppy disks I prepared it for 3.5" floppy disks. I used the design below. ... https://www.thingiverse.com/thing:4580018

Storage box for 3.5" floppy disks, with lid. ...Holds 14 disks.

Storage box with lid for 5.25" floppy disks. Holds about 20-22 floppies. This is version 2. ...The box now has a 1cm lower back to make it easier to remove disks.

I added interlocking features to help keep the box closed. Squeeze the sides to open! The Solidworks model is based on importing the existing STL's as solid bodies, and then drawing on top of them. ...This is my first attempt at modifying an STL in...

Brief Summary These are edge guards and an alternate set of dividers for the Floppy Disk Construction Kit. The edge guards prevent thin items from poking out of the structure. The dividers have diagonal slots to save plastic. Both models are...

Brief Summary These are edge guards and an alternate set of dividers for the Floppy Disk Construction Kit. The edge guards prevent thin items from poking out of the structure. The dividers have diagonal slots to save plastic. Both models are...

Designed to replace the original dividers for Allsop 5 1/4" floppy disk, storage boxes.