floppy drive enclosure 3d models
76573 3d models found related to floppy drive enclosure.thingiverse
This is an enclosure for a 5.25" Floppy disk drive. It contains a bottom part and a top (cover) part. You will need a printer, which can print more than 23cm in height. I printed my cover part using Spectrum PLA Premium Ivory Beige, which...
thingiverse
This is revision 5 of my Slimline Floppy Drive case, which can be used with both the DrawBridge PCBs that I make, but there's also enough room in there to fit an Arduino Pro Mini, Nano and an FTDI board if required. I printed these at 0.2mm layer...
thingiverse
An enclosure which allows you to use an Apple //c floppy drive as an external drive on an Apple ][+ or //e.
thingiverse
This is a enclosure for a bare 3,5 Floppy Drive. I designed it for use with Moppy. (Musical Floppys / Floppy Music) The sound/resonance of the Floppys gets better with this plastic enclosure. You can even put other drives on top and it still sounds...
cults3d
This is a enclosure for a bare 3,5 Floppy Drive. I designed it for use with Moppy. (Musical Floppys / Floppy Music) The sound/resonance of the Floppys gets better with this plastic enclosure. You can even put other drives on top and it still sounds...
thingiverse
I started a project a while back to allow you to read and write to Amiga floppy disks from within Windows using an Arduino connected to the drive. The project is very successful (see http://amiga.robsmithdev.co.uk ) , is fully open source and...
thingiverse
Any 3,5 inch drive enclosure with either cable at either top or bottom.
thingiverse
A 3D Printable Floppy disk case for this USB Drive: https://www.amazon.com/DSLRKIT-Flash-Drives-Thumb-Waterproof/dp/B07FCBCT4C/ref=psdc_3151491_t1_B002MCB54Y#customerReviews Glue together, slider in place.
myminifactory
On early Apple IIs, amongs others, floppy drives used a flat cable connection but newer machines such as the IIgs, early classic Macs and the Apple IIgs, used a DB-19 connector.For this reason, BMOW created an adaptor. More info...
thingiverse
A work in progress, this is a 5'' floppy drive by Atari, for the 8-bit series of Atari computers. ... http://www.atarimuseum.com/computers/8BITS/XL/xlperipherals/atari1050.html
thingiverse
3d scan of a a PowerBook 2400c external floppy drive. This STL is decimated to 1/20th the number of faces and smoothed in Blender so a more manageable size. I think I can get a better mesh out of the scan data. ...I have scans for the main body and...
prusaprinters
Dimensions taken from a Sony MPF 720 Drive engineering document.The pictures show a print using Prusament PLA Jet Black. Printed on a Prusa i3 MK3S+. Quality 0.20mm with supports. ... Model was rotated vertically so the curved...
thingiverse
This is a model of the Gotek floppy disk emulator I designed which can be used for sizing, display etc.
thingiverse
Disk II (or Disk ][ ) 5.25'' floppy drive, from 1978. ...Made with Autodesk 123D Design.
prusaprinters
Replacement for the Apple II Floppy drive front panel, including door.If you like my work, please consider supporting me on https://patreon.com/javmasterhttps://ko-fi.com/javmaster
thingiverse
This is a belt I made to repair my floppy drive. It must be printed from flexible material like TPU, possibly others, but TPU worked for me. ... It just takes a couple of minutes to print.
thingiverse
they have a hole to let the screw pass so you actually need a longer screw to tighten a floppy drive or a gotek drive. screws are m3 the hole here is 3.5mm diameter so it sould let the screw pass trough without too much problems. the spacer is a...
thingiverse
The Mitsubishi M4853 Floppy Drive I purchased from Ebay had a Broken Door Latch bracket, and piece of Faceplate missing. I disassembled the Door Latch Mechanism, measured all needed parts, and sketched them. My brother drew them in Fusion 360, and...
thingiverse
This is a replacement lever for a vintage Panasonic JU-475 5.25" floppy drive. The lever fits perfectly, no need to glue it in place. Prints in 5 minutes. Printed in white and painted for a better look. ...Designed with Blender.
prusaprinters
This is a belt I made to repair my floppy drive. It must be printed from flexible material like TPU, possibly others, but TPU worked for me. It just takes a couple of minutes to print. Category: Computer
prusaprinters
(Note of course that the 5.25" is the floppy disk size: the width of the drive itself is 14.6cm on the metal, and 14.9cm at the face.)These parts overlap together but screw onto the drive separately, not directly to one another. Both fit together...
thingiverse
... make it impossible to close the lid! Let me know if you know of any other Sun machines that use this part. Included: - Blender project, which has multiple models to assist in redesigns - STL file for a single wedge (the floppy drive uses three)
thingiverse
A slim slot-in DVD drive disguised as a 5.25-inch floppy drive, with functioning eject lever and activity LED. DVD drive used: LG GA50N, wires soldered in place of factory eject button and LED. Front panel and eject lever taken from a dead TEAC...
thingiverse
This is a replacement drive belt for the Citizen W1D 3.5" floppy drive. This drive was popular back in the 80's and 90's for laptop PC's because it is so thin. And it got that way by not using a direct drive motor to turn the disk. Instead they...
thingiverse
Casing for a 3 inch disk drive. ... You will need 4 M3*10 screws to fix the casing to the disk drive;
thingiverse
Super simple, quickly tossed together drive bracket for Macintosh Plus and similar compact Macs. Based off measurements from a real bracket. ... Test and let me know if it works.
prusaprinters
Casing for a 3 inch disk drive. You will need 4 M3*10 screws to fix the casing to the disk drive; Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: NoInfill: 0.2 Filament: Prusament PLA Notes: I get the best result with 3...