flower and stem 3d models

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: Yes Supports: Doesn't Matter Resolution: .2mm Infill: 10% Notes: I tried to get the MakerBot 2X to print the flower as one print but had disappointing results. I ended up...

flower leaves and stem wall art. ... I added them to the wall with small amount of blue tack just updated flower and fern type leaf as top 2 leaves were not printing correct and sunflower had holes on the bottom

I wanted to print out Markab's flower and a stem but not have any leaves on the stem. That way I will not have to worry about breaking any leaves off when I put it in a vase. I flattened the bottom and designed my own leave less stem. ... Filament for...

No description provided.

Created a stem for 3d printed flowers in 100, 150 and 200mm lengths. Stems can be shaped IE: put a 90 degree bend on the stem when removing from the heated bed. Or you could use a heat gun or blow dryer to warm up the stem to manipulate to any shape...

Used the stem from this Thing (minus the leaves) and adapted it to hold the Maz flowers: https://www.thingiverse.com/thing:2782116

I wanted something more realistic for the stem rather than skewers so I remixed the stem from here: https://www.thingiverse.com/thing:2789668 and removed the leaves, then added a smooth 3mm rod to the end, long enough to hold the Maz flower and...

Clip to hold plant stem or flower stem to support. The small ring is approx 5.5mm and the larger one in approx 7.5. ...Intended for TPU.

Cute 3d figurine of a dandelion flower and a ladybug.The figurine is divided into 3 subtools: a ladybug, a flower and a stem with a stand. ... All files are checked, the meshes are clean, closed, there are no foreign inclusions.

This Flower Keychain with Stem was designed to be quick and easily to print. ... Material: ABS or PLA (Successfully printed) Infill: >20% Layer Height: 0.1mm (to show small features) Nozzle: 0.4 Diameter

... think this is better than being too loose. You could always secure it with a little glue too. I printed it on my Anycubic Photon resin printer with the stem and bulb both upright and didn't need any support. ... I painted some of them afterwards.

This will actually be part of a larger piece but thought it works well on it's own. ... Can be used as a flower vase. The bottom has a shallow depth. I've put soil and stones in this area. ...I think a nice layer of moss will look nice too.

Added the stem and couple of flower elements. The flower is scaled 150%. Print the stem laying down with 100% infill to make it stronger. Print it and glue it all together. ...

Filament for stem is Just PLA's lime green: https://www.justpla.com/pla175mm/green-play175-1kg?limit=100 Filament for flower is Makergeeks soulful blue:...

I remixed the LEGO flower stem into three threaded pieces to eliminate the need to print with supports. Use the petals from DasMia's version. NOTE: I had issues printing the internal threads of the middle section. ... I wasn't able to get them to...

Bit of a mashup between: Rose and stem by patwik February 12, 2019 3423963 And Printable Rose Flower by Jerrill December 15, 2014 Like others mentioned, in the makes of patwik's model, I had print quality issues due to wall thickness and a noticeable...

Resized and added the function to screw the rose onto the stem. Support required when printing the stem. ...Raft recommended when printing the rose.

Stem 120mm - 6°

... printable with no supports. Also add a stem hole. Designed my own rose stem with thorns. Stem may need supports at least buildplate supports. There are variations: larger leaves and a rose base TIP: Use a heat gun to re-shape leaves and branches.

If you keep both models standing up (the flat side of the stem on the bed and the screw of the rose on the bed), then you will only need supports on the bed plate. I would suggest putting infill between 15-30%

I pulled the stem off and made it a separate part with a 10mm rod that connects the 2 parts, so you can glue it in. I scaled them up 135% for my prints but I left the models the original size. I haven't tested the fit at 100% scale, so I'm not sure...

More realistic aspect because slice honzontaly - Add Leave model designed in Fusion 360 by myself You can paste it on the stem. One or more leaves but for me only one is better. - Use heat gun or hot water to bend the leave to seem natural ...

... flaws in the bottom of the pettals on the bottom outside. ... I patched them so they look a lot cleaner. The Rose can be printed without support. Make sure you have good adhesion or use brim. Stem has not been altered. ... Printed in PLA 205/55

... some flaws in the bottom of the pettals on the bottom outside. ...I patched them so they look a lot cleaner. The Rose can be printed without support. Make sure you have good adhesion or use brim. Stem has not been altered. ... Printed in PLA 205/55

created a stem that a BIC Pen insert could be sliped into so you can write with the flower and refill as needed. The petals and center can be found on the original posting www.thingiverse.com/thing:2182466 A little support is needed under the ends...

When I printed the flower stem of this design https://www.thingiverse.com/thing:4798812 it didn't fit the lower connect part of the stem was too small. ... So I made it slightly bigger to snap fit better!

When I printed the flower stem of this design https://www.thingiverse.com/thing:4798812 it didn't fit the lower connect part of the stem was too small. ... So I made it slightly bigger to snap fit better!

created a stem that a BIC Pen insert could be sliped into so you can write with the flower and refill as needed. The petals and center can be found on the original posting www.thingiverse.com/thing:2182466 A little support is needed under the ends...

This is a remix of this: https://www.thingiverse.com/thing:5510218 I cerated a stem stand and a vase with a special stem, witch is hold the stem in the center of tha vase.

When I printed the flower stem of this design https://www.thingiverse.com/thing:4798812 it didn't fit the lower connect part of the stem was too small. So I made it slightly bigger to snap fit better! Category: 3D Printing