flysky fs i6 case 3d models

Tested with R9M module

has better mouting

My kids forced the steering wheel and a part that is connected to the brake disk broke off This is a reinforced version of that disk.

I built the clamp to attach goggles as a field monitor to the radio. The eachine goggles come with a standard tripod mount thread. To mount it, you'll need a 1/4" tripod screw - I salvaged mine from an old flashlight holder. ... Alternatively, you can...

Box for securing receiver with Cable tie to Model Base.

I got the concept from that design on Thingiverse, specifically this one https://www.thingiverse.com/thing:1324260. I slotted in two wooden dowels and attached antennas to each end. ...The model has been reworked entirely.

Hello everyone! I'm excited to share something with you. So, here it goes... I have extremely long hands. Yes, that's right - my hands are quite large. That presented a problem when I tried to use the UGFPV Nirvana transmitter because I couldn't get...

Tested with R9M module

Box for securing receiver with Cable tie to Model Base.

I remixed an awesome thumbsteer option for those of us with smaller hands. ...I have included the .stl of my addition which can be printed and adhered to the original and also the gcode for an ender 3 v2 where I combined the components in cura.

I designed these protective covers to shield the delicate battery caps of the NV14 from scratches. Simply print them out using a TPU material with an infill density of 100%. ...Due to their design, no support structures are required.

Steering and throttle trim bezel to help prevent accidental trim adjustments. 5mm thick, use double sided tape to secure it to the radio. ... 2 options uploaded: one with "ST" and "TT" text on the side, and one without the text.

A thing to hang your Noble on. The screw holes are level, 72mm apart. ...Make sure the left screw is flush so it doesn't touch the radio.

My kids jerked the steering wheel hard, causing a vital component attached to the brake rotor to snap off. ...This is an enhanced design of that very same rotor.

requires 2rubber bands

Designed to keep my receiver safer and secure.

This system was engineered to enable users to utilize any 12mm hex wheels for controlling steering inputs in their vehicle. ...From personal experience, the standard wheel proved to be slightly undersized, and this adapter provided the perfect solution...

The included mod-fs-cover-m10 in the Vertex published files is a course thread M10 connector. ...which is odd since the rear PTFE connector is fine threads.&nbsp;</p>

These are the enlarged M6 Thumbscrew and Bar used in Festool Deflector FS-AW by by ShapeLabs July 20, 2019. ... I enclosed the M6 nut in the bar by using pause print on line 18 in Cura 5.1

The 3D model was created from a genuine car base. It’s rendered accurately, using actual units of measurement, at a high level and in a way that mirrors the original. Model formats: *.max (3ds Max 2008 scanline) *.max (3ds Max 2008 vray) *.fbx...

This is a direct replacement for the stock kit transmission of an Axial SCX10.2, bolting directly to the stock skid plate. To mount it up front, motor mounts need to be added. It utilizes stock transmission internals throughout. Two aftermarket...

Mr. Steele is a legendary figure, revered for his unwavering dedication to the art of storytelling. With an unrelenting passion that borders on obsession, he crafts tales that transport listeners to realms both familiar and unknown. His words weave a...

Stepper motor visual model created from technical drawings as reference.

Customized version of https://www.thingiverse.com/thing:12345 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=12345 Instructions Using the following settings: haoMeasurement =...

Human-Created Version of Thingiverse Project Created Using Customizer App Instructions for Utilizing the Customized Options: To Get Started, Follow These Steps: Set Measurement Option D1a to Value 0 Adjust Measurement Option D2 to Value 6...

This file contains only the model without its associated environment. Modeled using 3DS Max 2010, the final images were rendered with V-Ray 1.5 SP4a. A high-quality model accurately scaled to reflect original object measurements in millimeters,...

So I designed 3 parts to adapt a PTFE tube to link the dryer to the FS Cover and keep the filament always out of humidity during printing. And you can let it in place after printing without fear of humidity. The FS Cover is the MK3S, with a M10x1.5...

FS i6B Mounting Plate Installation for the Martian II Frame: A Secure and Easy Solution I designed the FS i6B mounting plate specifically with the Martian II frame in mind, taking care to include a thoughtful gap that allows for secure fastening...

... a look that's unapologetically bold. Width (in.) 20.75 Height (in.) 12 Leadwire Length (in.) 114 Canopy Width (in.) 7.87 Canopy Height (in.) 1.97 Canopy Length (in.) 7.87 3d max 2014 fbx vray https://www.craftmade.com/bastion-49490-fs-led

... la estructura y prevenir la rotura de esas zonas. No es necesario modificar la emisora, se sujeta con abrazaderas de plástico de 5mm de ancho. Toda la información https://cet3d.top/proto36-rc-car-posts/fs-gt5-camera-tripod-mount-gopro-8-9-10/