flysky gt5 battery 3d models
72523 3d models found related to flysky gt5 battery.thingiverse
1 version is for using a larger rechargeable battery, and the other is to still use AA batteries. I like the AAs because I haven't found a rechargeable worth using. They both have a small compartment to store extra screws or body clips. I am...
thingiverse
I didn't want to hot glue the cover as I don't recharge from the side (great idea though) I wanted to have a direct replacement that could hold 2s lipo-battery. Two different models one that fits the battery shown perfectly. The other is more of a...
thingiverse
Was sick and tired of battery life on 4AA batteries. This allows the use of larger 2s Lipo packs to be used. previously you were limited to 800Mah 2S or smaller. ...with this, your able to use upwards of a 1500MAH lipo pack.
thingiverse
I didn't want to use AA batteries for my Flysky GT5, and I was tired of removing the tiny miniscule lipo over and over again to charge it seperately. So I decided to make a mod that not only housed 18650 batteries but also allowed me to charge them...
thingiverse
I wanted to customize my daughter's Flysky GT5, so I found a wheel design I liked and and used the center out of it to make a new steering wheel.
thingiverse
Outer donut/wheel for the Flysky GT5 radio. The original foam donut works OK on the GT5, but I prefer a rubber/TPU wheel for better grip. To install, unscrew the center wheel and pull it off the transmitter shaft. Pull off the foam donut and...
thingiverse
FS GT5 knob enlargement. Made this so I can turn the ch6 knob with my finger to rotate my FPV camera while driving. ... Might fit other knobs on FRsky transmitters.
thingiverse
Replacement wheel for the FlySky GT5 transmitter for one handed driving.
thingiverse
This mount system allows you to attach phones, cameras, lights, microphones, and anything else that uses either a 1/4" camera mount or a cold shoe camera mount to your Flysky FS-GT5. ... Non-3D printed parts also needed: 3-1/2" 1/4-20...
thingiverse
Very basic phone clamp for Flysky RC transmitted (FS-GT5). May fit others, uses M4 nuts and bolts and I used an M4 thumbscrew so the phone can be clamped on quickly and the angle adjusted easily. Hands free filming your RC's May be more stable if...
thingiverse
A 1 handed adapter for the FS-GT5 to enable 1 handed steering. No modification to the transmitter needed, just unscrew the steering wheel and slip this over the back. It's a tight fit so no glue required. ... I have included the Fusion 360 file and a...
cults3d
A 1 handed adapter for the FS-GT5 to enable 1 handed steering. No modification to the transmitter needed, just unscrew the steering wheel and slip this over the back. It's a tight fit so no glue required. ... I have included the Fusion 360 file and a...
cults3d
tape holder Compatible with ...Absima CR6P ...Flysky FS-GT5
cults3d
GoPro mount for FLYSKY FS-GT5 where you can connect different devices to record while driving your Crawler or radio control vehicle. Material: 2 screws m2,5x8mm 1 screw m5x45mm 1 nut m5 Installation: Remove the battery cover and attach the camera...
thingiverse
This is a spacer for use with Futaba Short 2 Position switches on the FlySky GT5. ... A brief How-To can be found here: https://m.facebook.com/groups/265365123944286/permalink/1141293756351414/?refid=18&ref=m_notif¬if_t=feedback_reaction_generic
thingiverse
This is a thumb steering adapter for a Flysky GT5 that also integrates a 12mm adapter to use a larger 1/10 foam onroad tire. This is for my bigger hands to give more control for crawling. It is a blend of 2 existing models and I am including the...
thingiverse
Made this for the missing part that was not included in the files.
thingiverse
Print as oriented. Fits snugly on the existing wheel. ...Hold in place with a little CA glue if needed.
thingiverse
My son and me enjoy long walks with our RC cars. It's much more handy if you don't need both hands to drive. As the other thumb steering ring/knob that I downloaded from thingiverse which was told to be a snug fit didn't fit at all (much too...
thingiverse
Remixed the main body to fill all of the holes and put a recess in the bottom to fit a GoPro flat sticky mount. ...Recess is 40mm wide x 50mm long x 13mm deep.
thingiverse
My kids forced the steering wheel and a part that is connected to the brake disk broke off This is a reinforced version of that disk.
cults3d
My kids forced the steering wheel and a part that is connected to the brake disk broke off This is a reinforced version of that disk.
cults3d
Remixed the main body to fill all of the holes and put a recess in the bottom to fit a GoPro flat sticky mount. ...Recess is 40mm wide x 50mm long x 13mm deep.
thingiverse
This has been designed to allow the user to use any 12mm hex wheels to control steering inputs to the car. ...Personally I found the stock wheel slightly too small, this adaptor allowed me to use a 1/10 foam tire which is slightly larger.
thingiverse
I designed a battery mod for the FlySky FS-I6. In the holder is room for a 18650 battery holder. With a Linear Voltage Regulator 7805 you can convert the 7.4v volt to 5 volt for your transmitter. You can connect the18650 batteries to your...
thingiverse
Battery mod for Flysky i6, it fits on the original cover insert and it's not needed to open the transmitter to solder. ... The board reduces the voltage from the battery to 6V, in this case I use 2S batteries with XT30 connector, which are 7.4V.
thingiverse
Replacement battery compartment lid for Flysky FS-i6 remote control/