flywoo vampire 3d models

CineRace20 duct replacement ! N.B. DON'T PRINT V1... I'VE DELETED IT! I DRAW VERSION 2.0 CORRECTING ALL THE ERRORS AND LOTS OF EVERYTHING AGAIN! ...GOOD FLIGHT TO ALL

Der Firefly Hex Nano kann eine GoPro Session ohne Probleme tragen, also hab ich ein Teil gemacht was es im richtigen Winkel hält. ...Hier ein Video wie es mit ReelSteadyGo dan aussieht: https://www.youtube.com/watch?v=_ZtU9lT4ce0

null

a simple design to mount ur gps buzzer and insta go2

Choose your angle and print! No Supports required. My runcam is dead, never start it up when the flex connector to the camera is unplugged!!! ... have fun.

This is too big of a GPS unit for this drone but luckily I don't give a duck.

Optimized mount for a Runcam 5 Orange on a FWE LR Frame Lighter in compare to the origin. And with a border in front to avpoid to lost the cam. ... Weight is 3,5 g printed with 15% infill.

Not sure about this canopy on this quad as it's 4 grams when printed from PLA (original is 1.1g) and I also added 2 more grams by using nano camera and 0.8g buzzer :) But maybe someone can remix it or it will be usefull on heavier quads with 25x25mm...

Must print in tpu

Getting the satellites to connect before takeoff for rescue mode is time consuming. It seems I connect a little quicker if I tilt the quad nose up allowing the gps antenna to angle more toward the south. Most of the antennas are mounted at an angle...

I designed this Gopro Hero 8 Mount for my 7'' mr.croc because I didn't found one on the Internet. ...There is a 15° and a 25° mount you can choose between for more cinematic flying or speed.

First: Big props go to the original creator: MatStevenson I just remixed it for the community and me to have different angled versions. Sharing is caring :) It makes use of the mount on the camera to secure it in place. Works with the factory...

Summary

Battery holder for R-line 550 2S batteries to fit in the Firefly 2SInternal measurements 18x14.5mm in case you have a different battery.Prints in TPU with no support

Mount GPS GM10 A-12-01 Nano V3

Printed in PLA

Remixed from the Idahobo guard to work with the dead cat frame. ...Remove the 4 plastic nuts and use the prop guard in their place.Uploaded a V2 that has some weak points beefed up a bit.

I wanted to move the GPS further away from any interference so I designed the 45mm GPS extension which moved the GPS 10mm further back. I then used some metal braid to shield the entire length of my GPS wires which made them straight. Since I...

5 Degree and 10 Degree Camera Canopies.

I switcht from the Caddx Ant to the Caddx Baby Ratel 2 and its a bit longer so i had to modify the design

Conical Support/ Tree Support 100% infill Print it with the side down. ... Nice fixed when turn

<p>print it out of tpu</p>

This set includes 1 miniature.  Fully pre-supportedEasy-to-print !Easy-to-paint ! ...  Join us on our Discord : https://discord.gg/TecnyN3 Join us on Tribes : https://www.myminifactory.com/fr/users/VaeVictisMiniatures

This set includes 1 miniature.  Fully pre-supportedEasy-to-print !Easy-to-paint ! ...  Join us on our Discord : https://discord.gg/TecnyN3 Join us on Tribes : https://www.myminifactory.com/fr/users/VaeVictisMiniatures

You will have 2 files: One for the Dice Tower Base part, One for the Dice Tower Top part. These files are optimised for FDM (PLA Filament) 3d printing. These files are for non-commercial personal use only. ... For further information and to support my...

Gems: rounds 4 pieces 2.5 x 2.5 mm D. Ring sizes inner diameter: |17mm|17.5mm|18mm|18.5mm|19mm|19.5mm|20mm|20.5mm|21mm|21.5mm|22mm|22.5mm|23mm| And size USA 11 Recommended material - silver or gold! Approximate metal weight (for ring size 21 mm):...