▷ fn 5 7 3d models 【 STLFinder 】

FN 5.7 BARREL ASSEMBLY
grabcad

Barrel Assembly for the FN 5.7x28mm Pistol.

FN 5-7 Hip Holster
thingiverse

Thanks Danteel for your holster, with a few modification it fits the 5-7 quite well ! ... It's for right handed, but if you are left handed, just mirror the desing

FN 5.7×28mm
thingiverse

Needed a model of this cartridge for modeling storage cases. Everything should be dimensionally accurate except for the curve of the parabola of the bullet which I modeled to look about right. I got the dimensions from Wikipedia article. I...

RMR mount for Marushin FN 5-7 & VFC Glocks
thingiverse

The rear sight and securing pins must first be removed to fit the Marushin 5-7. Not compatible with Marui 5-7/Glock. 마루신 파세와 vfc 글록용 RMR 마운트입니다. 잦은 RMR 탈부착은 나사 고정부 손상을 야기할 수 있습니다. 더불어, 출력물은 출력 재료와 방법에 따라 쉽게 파손될 수 있습니다. ... 마루이 5-7/글록과는 호환되지 않습니다.

FN 90 magazine cal 5.7
grabcad

FN 90 magazine cal 5.7

NATO STANAG 5.7MM Headspace Gauge (5.7×28MM FN)
grabcad

This is the NATO spec headspace gauge for the 5.7×28MM FN.Operation:Rotate the threaded base so that the desired length has been obtained, once satisfied, lock the base into position by use of the internal screw.The value "X" is the measurement of...

5.7×28mm "Hyposone Architecture like”, asymmetric Suppressor for FN P-90
grabcad

5.7×28mm "Hyposone Architecture like”, asymmetric Suppressor for FN P-90 Calibers: 5.7x28mm Specs: 6.5 inches long x 1.5 inch OD x 19.25 ounces 7 x Slanted & Ported Baffles (60 and 75 degress) Materials: Stainless Steel 304L and Aluminum 7075/T6...

5.7x28 FN Bullet
grabcad

5.7x28 FN Bullet for simulations etc.

FN 5.7x28
grabcad

This is a 5.7x28 round made by FN. ...I drew the bullet for use in a future project and figured others might find it useful.

FN STYLE 7.62 X 51 MAGAZINE
grabcad

FN STYLE 7.62 X 51 MAGAZINE

FN 7.65 browning 1922 Grips
thingiverse

FN 7.65 browning 1922 grips Print Settings Printer: k8200 Infill: 15%

FN FAL for 5.5 inch figures
thingiverse

Adapted a model of an FN FAL for use with the 5.5 inch scale Doctor Who figures, should be roughly in scale. Would only recommend resin printing this. ...Be wary of the barrel being thin and fragile.

LA-5 FN Low-poly 3D model
cgtrader

La-5 (original name - LaGG-5) is a Soviet single-engine fighter, created in 1942 by OKB-21 under the leadership of S. A. Lavochkin in Gorky. ...Produced from July 1942.

FN 5.7x28mm Bullet Clip Holder
thingiverse

Simple clip for holding 5.7x28mm ammo (5 rounds). I printed my 9mm version of this to easily access tightly stored ammunition. Check out the pictures from that design for easy use instructions. If you printed any of my ammo box designs, this...

FN 5.7mm ammo
thingiverse

found a blueprint at google, so i made it same. ...no support needed.

7.5
thingiverse

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: Font = write/orbitron.dxf ring_width = 7 font_spacing = 0 message = V I P ring_size = 17.73 font_size = 10 ring_thickness = 1.6

FN
sketchfab

No description provided.

Fn
thingiverse

Customized version of https://www.thingiverse.com/thing:2783650 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2783650