foldable phone case 3d models
249169 3d models found related to foldable phone case.thingiverse
This is a remix from https://www.thingiverse.com/thing:398515 I just modified the base and the stop to be able to accommodate a phone with a thick case. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:1666131 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1666131 Instructions Using the following options: Tilt...
thingiverse
If you have lost or broke the foldable cover from your beloved phone case for Samsung Galaxy s9+ or s10+, don't go further! Print it standing on long side for best result. Try to keep warping minimal! There is also a flat version (without logo)...
thingiverse
If you have lost or broke the foldable support from your beloved phone case for Samsung Galaxy s9+ or s10+, don't go further! Print it standing on long side for best result. Try to keep warping minimal! There is also a flat version (without logo)...
thingiverse
This is a foldable phone stand. ... It prints as one piece. Tested with iPhone 8 and iPhone 6s Plus including case, but other phones should work. ... Refer to dimensional drawing to confirm compatibility.
thingiverse
Foldable Stand for Phones / Tablets The hinge is made with a piece of 1.75mm filament
thingiverse
Foldable mobile phone stand. ...Assembly requires a paper clip and a piece of filament.
myminifactory
This is a remix. ... Original design: Foldable Phone Stand Original design by: @ClementCrd
thingiverse
One more cell phone stand. One piece foldable! ... Have fun BR Slopy
thingiverse
foldable phone stand with adjustable angle > print in place < 116 x 90 x 12 mm
cults3d
Foldable design, folded up only the size of the bank card, easy to carry, can place mobile phones and tablets.
thingiverse
Quick foldable phone stand for phones up to 10mm thick. Print as-is. No supports needed. Use 1.75mm filament for hinges. ...
cults3d
Quick foldable phone stand for phones up to 10mm thick. Print as-is. No supports needed. ...Use 1.75mm filament for hinges.
thingiverse
This is a foldable phone holder printed in one piece no supports. ...Also made a box for protection in travel use.
myminifactory
Is a remix for Foldable Phone Stand make by Clement C. ... I put some hinges in flex point doing it more durable, increase a litle bit the thickness.
thingiverse
Foldable stand for phone and tablets. ...After print support structure on the swivel remove and turn slowly so that it does not break.
thingiverse
This is a 2 parts foldable phone holder. ...The base (bottom) part can be printed without support, the top part must use support.
cults3d
A foldable phone holder. Snap together (no glue, no screws). Once folded it easily fits in a pocket. ... Suitable for any type of phone, with or without a protective shell.
thingiverse
This is a foldable phone stand that has a low profile once folded. It can be fit in a wallet or pocket and used in portrait or landscape mode on the phone. ...Print with 0.12 resolution for best results
cults3d
Hello, I am sharing today a foldable phone stand, can also be used for tablet or photo frame, in landscape or portrait mode. Created following a request from my daughter ;-) As it is foldable it can be stored without taking up space, ideal for the...
cults3d
Foldable phone holder for viewing videos, selfies, photos. It has a small size and fits easily in a pocket. ...For assembly, you will need a screw M3x20mm and a small piece of wire with a diameter of 1mm.
cults3d
Very compact foldable phone stand. Which fits all sizes of smartphones. ... Dimensions folded: 6.6 x 6.6 x 1 cm Dimensions unfolded : 8.4 x 6.6 x 6 cm
thingiverse
Smart Foldable Phone Stand. The Model is consists in 3 pieces: - Left Part - Right Part - Pin Print Them all and glue the bottom part of the pin to the adjiacent wall. ... Tip if you like it!