folding quadcopter 3d models
24320 3d models found related to folding quadcopter.cults3d
I left the front of the quadcopter open because I plan to design a case to fit in front of the quad for GoPro camera, and later even a gimbal for the GoPro (not sure if the quad can lift the camera with the gimbal yet) The battery goes under the...
thingiverse
I left the front of the quadcopter open because I plan to design a case to fit in front of the quad for GoPro camera, and later even a gimbal for the GoPro (not sure if the quad can lift the camera with the gimbal yet) The battery goes under the...
cults3d
- Erection of motor axes 5 degrees - The size of the motor mounting - 16x19 mm Provided internal wiring in the folding beams, foldable gps antenna mount and folding legs. In a closed frame case, any flight controller can be installed. There is an...
pinshape
- Erection of motor axes 5 degrees - The size of the motor mounting - 16x19 mm Provided internal wiring in the folding beams, foldable gps antenna mount and folding legs. In a closed frame case, any flight controller can be installed. There is an...
thingiverse
Складной коптер 450 мм диагональ под Pixhawk или APM. Требуются: профиль 10 мм алюминий карбон трубки 4 ммм для ног винты гайки шайбы М3 виброплатформа для APM При сборке советую распечатать детали, а уж потом, используя их как...
thingiverse
Складной квадрокоптер. Изначальная идея не моя, но человек делал "руками": http://forum.rcdesign.ru/blogs/121800/blog22371.html Переработал все для 3Д-печати. основа - алюминиевая квадратная труба 10мм, из которой нарезаны лучи и лонжероны...
thingiverse
All pieces are meant to be laid flat so that they are printed with the most strength possible. I've chamfered some bottom edges to make it easier to put together some of the piece as well. The holes on the front edge of the rear top plate are meant...
cults3d
- Erection of motor axes 5 degrees - The size of the motor mounting - 16x19 mm Provided internal wiring in the folding beams, foldable gps antenna mount and folding legs. In a closed frame case, 5s6p cells 18650 can be installed. There is an...
thingiverse
Yhe goal was to create a folding quadcopter that uses standard ESCs and flight controllers. So, this is larger than a Mavic or Vitus. It is 400mm motor to motor diagonal. So far: -920KV motors -30A ESCs -10" folding propellers -3S 5000mah battery...
thingiverse
... The battery box (below the copter) and the brackets for a NAZA are attached with M3-12 screws and nuts. Motors are attached to the motor brackets with M3-8 screws. ESCs are ziptied to the boom arms. The quadcopter comes in at 30oz with battery.
thingiverse
For those times when the grass is just a bit too long and it gets tangled up in your propellers as you try to take off, use this handy folding launch platform to raise the quadcopter up a bit. Designed for a DJI F450 frame to sit on, but will...
thingiverse
this is still a works in progress, but seems to be ok, just need to test the motor mounts the booms are 12mm carbon tubes Print Settings Rafts: Yes ...
cults3d
This is Expire, any similarity to a big brand commercial quad would be only coincidental, it is a simple modular quadcopter which can be quickly folded for optimum compactness in transport despite its size. With 15 "folding propellers:...
thingiverse
Variety of clamps and links for 16mm carbon tubes used in my copters
thingiverse
Quadcopter inspired by the flower of life from sacred geometry Print Settings Printer: Prusa i3 Rafts: Yes Supports: No Resolution: 0.2 Infill: 83% Notes: keep perimeters low (
thingiverse
A folding leg set that fits the DJI 450 Flame Wheel style quadcopter. ... This makes storing your machine much easier yet gives clearance of the underside to wet grass etc.
grabcad
folding arm mechanism for quadcopters/drones for 16mm diameter 2mm thickness carbon fiber pipes
thingiverse
Another weekend project, still on progress, hope it's can fly away :) Preferred specs: - ABS filament or any strong light filament and heat resist - Using 12mm tubes for arms - 4S lippo / custom li-ion battery - Naza lite/v2 flight controller ...
grabcad
A working concept for a 3D printed drone that is compact, foldable and can be easily and cheaply 3D printed. ...Think almost disposable.If you are interested in this design or would like source models, please contact me.
grabcad
8x #8-32 nuts 8x #8-32 Lock Nuts 8x #8-32 screw 0.75 in long Assorted Cable Ties ~4in long - Use as necesary, min 8x needed #INSTRUCTIONS {TO DO} :-) Links: Motor: http://www.headsuphobby.com/Emax-MT1804-2480kv-Motor-CCW-Rotation-A-080.htm ESC...
thingiverse
I thought I'd try my hand at creating some custom landing gear that also can fold up. These are designed to use a 3mm diamter screw (probably 20mm long) and also use a foam ear plug (cut in half) at the bottom. I'll upload a photo once I try it...
myminifactory
Basically, it can be launched using a rocket model motor (common Estes Rockets stuff), and it can be retrieved using the electric motors of the quadcopter, landing the rocket vertically (SpaceX style). https://www.youtube.com/watch?v=JehjgXvUAzA...
3docean
HighDetailed Folding style QuadCopter Drone. Inside PCB bord, Motor, Gears, Battery… all exist. Folding Arm, Folding Prop…All can move it. You can choose open/close PropArm. You can open battery slot and can move battery itself. You can change...
thingiverse
... friend who lost his carbon fiber landing legs in a crash. ... They are designed for [this quad](http://www.hobbyking.com/hobbyking/store/__78142__DYS_250_Glass_Fiber_Folding_Quadcopter_With_Storage_Case_PNF_.html), or others with arms around 14mm wide.