folgertech ft5 3d models

I decided the factory limit switch mounting wasn't up to my standards, so I designed one myself. It's a solid fit thanks to two T-nuts, which provide plenty of stability. The 0 point can be adjusted by shifting this fixture along the Y axis on its...

I'm remixing this design from the original at Thingiverse: http://www.thingiverse.com/thing:83680. It's optimized for 8 mm rod. ... This model was created using Tinkercad and can be edited online at https://www.tinkercad.com/things/fm4QawoPaMp.

A customized connector for the RJ45 breakout board is designed to be mounted on the rear of the X carriage support structure.

Prusa i3 Fan + BLTouch Mount is now optimized for extra space. ... Functions seamlessly with the fan manifold found at: http://www.thingiverse.com/thing:1161013

This design calls for a 1/4 inch thick piece of plexiglass that needs to be cut and securely attached to the underside. Pre-drilled slots are in place to accommodate 6-inch wide acrylic hinges, which can be easily sourced from Amazon. The choice of...

I began using bigger spools from Spool3D and Filaments.ca, but the old holders were too small. I added a top section that lifts the taller spool high enough to clear the Extrusion below. ...Alternatively, if you've already printed the original arms and...

I'm using this design with the Kossel 3D printer to place the power supply unit below it. ... Print Settings Printer: Kossel Rafts: Doesn't matter Supports: No Resolution: 0.3 Infill: 30%

The assembly demands a pair of 3mm x 16mm long screws and two 3mm Nylock nuts to secure it properly.

I needed something to hold my cabling tight, so I used an M4 screw and bolt setup that I had on hand. You have to tighten the screws all the way down or the holder will slide, but if you do it'll stay put. Will this work for your printer? To be...

Replacement spool holder for the FT-5 designed to sit perfectly within the frame's dimensions. The goal was clear: a holder that wouldn't hang over the edge, providing a sleek and organized look. Additionally, it had to be entirely 3D printed,...

After several hours of working with a linear actuated dial indicator on a sweep arm, I discovered the rear bearing mounting position was not as rigid as required for accurate return to home position. This revised version -completely new files and...

One of my first upgrades to the Folger Tech Prusa I3 was a significant improvement that utilized a more robust solution for the Z endstop. This design mounts directly onto both the x-axis motor and the z-axis motor mount, providing a rock-solid...

I fashioned this makeshift holder using SketchUp as a temporary solution for storing a handful of essentials. ...It's currently secured to the top of the printer, but I've made some updates to accommodate a few additional items.

Utilize the standard issue control panel.

The stock fan is blowing air everywhere. I struggled to get the bed to heat up fast, and then there were problems with delamination when using ABS. I created this to fit under the fan, countersinking the heatshrink. The ducts route the air straight...

I upgraded my Cloner's auto bed leveling feature and it functions flawlessly. Since I'm only utilizing a single extruder, I repurposed the unused side of the extruder mount to attach a Z probe. My prints are coming out great with 20% infill in ABS...

The standard extrusions proved too bulky for the t-nuts to securely fasten the rods, even when tightened so rigidly that the plastic began to fissure. Most of them could be easily shifted by hand! They were also made from PLA, which melted under the...

LED ring designed for Folger Tech Kossel 2020 3D printers. Accommodates 9 5mm LED lights. Attach it securely at the base of the fan. Ensure proper clearance for the auto leveling servo arm to function efficiently. This design is a modified version of...

<p>This is made to use uxcell Drag Chain Cable Carrier Open Type that is 10mmX11mm for its ease of cable install and is on amazon</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Monoprice</p> <p class="detail-setting...

Extruder Adapter with Enhanced Ventilation Support and Advanced Sensor Capabilities. Compatible with: https://www.thingiverse.com/thing:1234567 Note: This adapter is designed for optimal performance, allowing you to print with precision and...

We need half an inch PVC pipe for printing.\nThe standard spool design of this 3D printer is a thing of the past. This outdated design reduces the resistance the spool provides when the extruder pulls plastic through. ...It also doesn't get tangled up...

The modification of the CLeFranC design, to accommodate the measurements of the Prusa i3 Folger Tech model.

UPDATE: Re-uploaded the STL files with units in millimeters. Added X ends for five-millimeter threaded rods on August 6, 2015. The motor and idler came from the kit's original STL files, modified only to fit the leadscrew nut. An additional...

I simply use a 100mm extrusion profile cover that fits seamlessly into the 3D Builder software on Windows 10, allowing for easy cutting when necessary. ...The sleek design also provides a tidy way to conceal my cables, resulting in a visually appealing...

I'm impressed by wakuhn's Kossel 2020 Smart LCD Controller Enclosure (http://www.thingiverse.com/thing:1237708), but I didn't want to disassemble my Delta Printer to attach the enclosure, so I took the easy route and added some tabs on both sides. I...

I utilize this innovative device (http://www.thingiverse.com/thing:40024) to safeguard the connectors. ...This ingenious creation was expertly crafted using Tinkercad, and can be easily edited online at https://www.tinkercad.com/things/0q3TLEVw9tf

This design is compatible with the adjustable Z end stop trigger created by kyletmears, which can be found on Thingiverse as thing:1175592.\r\n\r\nThe original stock end stop was lengthened to ensure proper alignment for the screw from the trigger,...

Meet "The Boron" This is a total conversion for the Folgertech FT5-r2. The result is a CoreXY printer, with a belt-driven, quad-leveling gantry. I call it the "Boron" because it's a b*st*rd version of the Voron printer -- essentially all the neat...

This is a revised design for my previous BLtouch mount with 25mm Y-Axis offset, tailored specifically for use with the volcano hotend.\nhttps://www.thingiverse.com/thing:3241244\nThe BLtouch bracket has been lowered to match the height of the volcano...

This is a cutting-edge cooling fan engineered to cool both sides of the filament efficiently. To access additional files, visit http://www.thingiverse.com/thing:1666994. This project requires specific hardware components including -2x-4x m3 nuts and...