folgertech ft5 3d models

Replacement Component for End-Stop on Folgertech Prusa I3. End-stops can be located on either Y-Max or Y-Min, as both positions are suitable for this design. The end-stop is specifically designed to work with acrylic beds attached to linear...

Power Supply cover for the folgertech kossel with a mount for a plug and switch. Print Settings Printer: Kossel Rafts: Doesn't MatterSupports: No Infill: 10% Notes: Designed in solidworks. Built for Kossel Power Supply Printed on a Folgertech...

Print Settings Printer Brand: RepRap Printer: FolgerTech 2020 Prusa i3 Rafts: No Supports: No Resolution: .2mm (not a critical setting) Infill: 20-30% Notes: Printed on my FolgerTech 2020 i3 with some cheap unknown ABS that my friend gave me for...

Inspired by VoronDesigns Voron 2 skirt, I designed this complete base for the Folgertech i3 2020. Includes provisions for a bottom cover to mount all the electronics including a Raspberry Pi 3 or 4. A single cooling fan (70mm or 80mm) to provide...

I've redesigned the folgertech bearing setup, starting with a remix to simplify installation. Revision 2 includes improvements that make inserting the bearing more accessible. In revision 3, I removed the lower portion of the bearing mount to make it...

This is an overhead spool holder designed specifically for use with the FolgerTech Kossel 2020, utilizing an M8 threaded rod to accommodate up to two spools of filament at once. To ensure smooth movement and effortless loading/unloading of filament,...

This mount empowers users to seamlessly integrate an E3D Aero with a pancake stepper, paired with a powerful 15X50 radial fan, directly onto an FT5 without any required modifications or compromise to their valuable print space.

After spending a while searching for a better Y endstop, I decided to create my own custom solution for my Folgertech-built Prusa i3. This DIY project houses a 40mm long endstop switch board and fits perfectly in place, ensuring that my extruder...

The cooler from Folgertech Google Drive has woefully inadequate airflow to make it usable. For an axial fan used in 3D printing, extremely strong airflow is possible. Printed with PLA plastic. Aluminum adhesive foil serves as heat protection. No...

Other mounts can be found here: T-Motor FT5 225 SMA VTX Antenna + Immortal T Tail Mount: https://www.thingiverse.com/thing:4600592 Modular FPV GoPro Session Mount - T-Motor FT5 225: https://www.thingiverse.com/thing:4600593 Modular FPV GoPro Session...

Print Settings: Printer: Folgertech 2020 Prusa i3 Rafts: None Supports: None Resolution: .2 - .4 Infill: 50% Notes: Feel free to use any resolution you prefer. Since this part doesn't move or exert stress, the print quality and surface finish aren't...

... plate, users can enjoy enhanced reliability and stability in their 3D printing operations. The FT5 Extruder Carriage Proximity Sensor Mounting Plate is an essential upgrade for makers and hobbyists seeking to refine their printing experience.

When I assembled the FT5 Fang part cooler, I noticed that X would no longer properly locate its position. To resolve this problem, I created an adapter that fixes the issue. ... Thanks to DuMonYu's excellent design for making this possible.

... into place using two standard M3 bolts directly into plastic (holes are 2.8mm). This item is printed with ABS material. Tip: Use 3D-Tool for a detailed look at this design. Print Settings Printer FT5 Rafts No Supports No Resolution 0.3mm Infill 40%

These are cater mounts designed specifically for use with the 3in casters from harbor freight to allow your FT5 to roll around. The wheels are held in place with an M5 nut and bolt. I have been using these for over a year with no issue. ... 3in...

... a web-based 3D modeling tool. ...To make adjustments online, visit https://www.tinkercad.com/things/jlfeW735SGc. The design is tailored for the Folgertech FT-5 and other printers that feature extrusion frames, with a specific focus on the TFT28 case.

... using the two 5mm bolts on the 2020-profile. Suggestion: Use 3d-Tool to get a detailed view of this item. Print Settings: Printer: FT5 Rafts: No Supports: Yes Resolution: 0.3mm Infill: 20% Notes: This was printed with a 0.6mm nozzle in ABS.

Print Settings: Printer: FT5 Rafts: They're not necessary in this case. Supports: None are required for this print job. Resolution: A low setting is sufficient. Infill: 20% should be more than enough. ... Notes: I used four perimeter shells to...

These are cater mounts designed specifically for use with the 3in casters from harbor freight to allow your FT5 to roll around. The wheels are held in place with an M5 nut and bolt. I have been using these for over a year with no issue. ...3in caster...

I thoroughly over-tightened the square lock nut for part FT5 in the Folger FT-5 printer kit, causing irreparable damage to the parts involved. The screw was excessively long and its intended channel woefully inadequate. To rectify this issue, I...

Designed for the Folgertech FT-5 with the E3D Titan Aero, this print is tailored to perfection. After thorough testing, it was found to be a snug fit, but fortunately everything fell into place on a friend's machine. Another user has cautioned that...

After swapping out the Folgertech FT-5's standard MKS Gen 1.4 board for the Duet Wifi unit, I required an adapter plate to mount the new board within the control box. As it is recommended to cool the Duet from below, I designed a mounting system...

See http://www.thingiverse.com/thing:2045169 for a revised version, which includes belt tension adjustment done with the pulley rather than the stepper Print Settings: Printer: FT5 Rafts: No Supports: Yes Resolution: 0.4mm Infill: 60% Notes: I...

This is a fresh design for the Titan-Aero upgrade on the FT5. Since the new combination is shorter, I created a more compact header based on the original designs - back and header. The base of the header aligns flush with the bottom of the stepper...

This is a simple mount designed for Dual RJ45 breakout boards, intended to attach to the back of a 713Maker Ultralight FT5 carriage. The screw holes for the aluminum plate were created using the supplied drawings, so they are accurate. The mount...

The Folgertech FT-5 Extruder Cable Management Solution

Left Side End Stop Mount for Folgertech FT-5 Z.

Extended the lifespan of the mounting system by adjusting the belts to perfectly synchronize with the FT5 model's specifications.

Modular mount designed specifically for the FolgerTech Prusa i3 printer, integrating an inductive proximity sensor with seamless integration into existing stock screw holes from FolgerTech.

FolgerTech FT-5 Spool Holder Adapter slides directly onto the original spool holder.