ford explorer cup holder insert 3d models
451364 3d models found related to ford explorer cup holder insert.thingiverse
I modeled and printed replacement cup holder inserts for my 2016 Ford Explorer. The model is 80mm which will fit the front cup holder. ...Down size by about 10% to 70mm for the rear cup holder.
cults3d
I modeled and printed replacement cup holder inserts for my 2016 Ford Explorer. The model is 80mm which will fit the front cup holder. ...Down size by about 10% to 70mm for the rear cup holder.
thingiverse
I designed this cup holder insert to keep my 16.9 fl oz Diet Mtn Dew from rattling in the cup holder of my 2008 Ford Explorer.
thingiverse
Remade Cupholder. ...This cupholder is one inch deeper. The original was not deep enough and did not hold bigger cups.
cults3d
This is a cup holder insert made for the 2015 Mondeo/Fusion for smaller cups in the center console. Might fit other Fords. ... Much like the original supplied with the car but a little taller and wider to account for smaller cups and the slightly deeper...
thingiverse
This is a cup holder insert made for the 2015 Mondeo/Fusion for smaller cups in the center console. Might fit other Fords. Much like the original supplied with the car but a little taller and wider to account for smaller cups and the slightly deeper...
prusaprinters
This is a cup holder insert made for the 2015 Mondeo/Fusion for smaller cups in the center console. Might fit other Fords. Much like the original supplied with the car but a little taller and wider to account for smaller cups and the slightly deeper...
thingiverse
This is a special insert designed to it into the 2019 Ford Edge console cup holders. Not sure who the idiot at Ford was that designed these oversized cup holders with lock jaw brackets. The fingers on the sides of the cupholders are so tight that I...
thingiverse
Basic Cup holder insert for a 2016 Ford Expedition to hold a pop/soda can.
thingiverse
Designed for a 2013 Ford Fusion cup holder but will likely fit most cup holders adequately. Holds: 2013 Ford key fob, nail clippers, breath strips, chapstick, and has a large pocket for other miscellaneous items. Be sure to print in a material...
thingiverse
(Update: Seems to be a hair to big at the upper lip, will scale down and repost) Needed a replacement cup holder insert for my son's 1993 Ford Bronco. Haven't tried it for fit yet but the dimensions are almost exact. ...(Left side is printed, right is...
thingiverse
A cup holder insert to keep averaged sized cans in place while driving for a 2005-2010 ford explorer and explorer sport trac.
thingiverse
Goes with https://www.thingiverse.com/thing:4461392 Can insert for bottle insert. ...Will also work with the smaller water bottles but will be more snug.
thingiverse
... a 2018 Ford Explorer center console. ...Allows a phone to be stored and out of the way without taking up cup holders. Can easily be modified to fit different sized phones. ...This one was designed to fit a iPhone 11 Pro Max with an Apple Silicone case.
grabcad
This is for the guys that bought or buying an 2014 Ford Explorer Interceptor . This can be printed as a filler for the stock console shifter hole. Assuming you leave the shift on the column. I had a friend print mine and added an arduino with...
thingiverse
Being that 2016 and up Explorer center consoles do not have the chrome ring like previous model years, a bigger shift cup is required. Measurements were made of the shifter hole and various test prints were done in order to achieve the correct...
thingiverse
Made slices in the bottom with razor blade and used silicone adhesive to keep snug to door cupholder, will see if keeps if from pulling out when I grab my vape (I could probably use a fraction more clearance in the box mod cutout) Problem was cup...
thingiverse
The Ford Explorer Phone Mount was a great start. I enhanced it to angle the holder toward the driver and pitched it back as far as I could without having it hit the tray cover when it raises. It looked a little plain in my truck so I added the ST...
prusaprinters
A better version of this coin holder is supplied with the PLATINUM model of the car.I removed the deep pocket since it impared the printing too much for my needs.I think it would fit other vehicules as well, the original part number is...
thingiverse
This is a base for a Ford car cup holder. It stops cans and cups going all the way to the bottom of the cup holder. Infill of 15% should be fine. ...The flat part goes at the top and the fins go at the bottom.
thingiverse
I made a Ford cup holder separation with a 19 mm hole. For example, you can use a button for an additional horn. You can sand the surface, but be careful not to destroy the tips. ...(like in the picture)
thingiverse
MY stock Ford cup holder was not practical. This new design works great! Hope this helps you out like its did me, Coffee is life my friend. ... 2 designs if i mount the Double cup i'll post pic for now i like the 2 cups mounted to the T joint.
thingiverse
This Project is to Add Cup Holders to my Ford E350. It only came with one and it wasn't enough. So i used my E150 Wooden One as a template to make one for my E350. This can be resized to fit almost any Van Center Console. To Make the opposite...
myminifactory
This Project is to Add Cup Holders to my Ford E350.It only came with one and it wasn't enough.So i used my E150 Wooden One as a template to make one for my E350.This can be resized to fit almost any Van Center Console.To Make the opposite side just...
thingiverse
Here's a cup holder (and change tray) for 1987-1993 Mustangs. The cupholder slides down into the hole left by removing the ashtray. Tested driving with a full cup of water and it never fell out but it is a bit tougher to shift. However shifting...
thingiverse
2011–2016 Ford Superduty Cup holder Insert Designed to Fit Nalgene Bottle. Added holes in the sides to fit ram mount balls to hold phone. ... I will try and upload the standard one too.
thingiverse
this is a cup insert for my ford focus 2012 i made this to hold my camera rig
thingiverse
This an insert for the cup holder in the center console of a 1995 Ford Bronco Print Settings Printer: Zortrax M200 Rafts: Doesn't Matter Supports: Yes How I Designed This I measured the original part and then made a model of it in Solidworks
thingiverse
Can be used to create a cup holder insert so that any cup can fit tightly inside a cup holder. ... Could also be used for other applications.