ford fus 3d models
8282 3d models found related to ford fus.thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=489855 Instructions Using the following options: Gesamtbreite = 20 Texthoehe = 20 Plattenhoehe = 5 Text = fus Grundform = 3 Gesamtlaenge = 61 Textart = write/Letters.dxf Textfarbe = blue
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=402685 Instructions Using the following options: Textfarbe = red Gesamtbreite = 20 Gesamtlaenge = 68 Plattenhoehe = 2.5 Grundform = 1 Texthoehe = 15 Textart = write/Letters.dxf Text = FUS
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=489982 Instructions Using the following options: Plattenhoehe = 2.5 Grundform = 2 Textfarbe = green Textart = write/orbitron.dxf Gesamtlaenge = 57 Text = FUS Gesamtbreite = 25 Texthoehe = 10
grabcad
... me and this was the end result. They are called Han Fus. Making them I did take measurements of the ripples and what not. We took 1st at State and are going to Nationals in June. ...:) http://www.iltsa.org/National_High_School_TSA_Competitions.pdf
cults3d
plasma fus for cogbot magos this will also be in a packscale up 10% for 40thousand or alone
thingiverse
i've tried to combine/mix two stl files to get the insta360 go mount i need for the fus x111 cinewhoop
thingiverse
This is a LIPO_Holder for the Fus_Spartan_v3 It's for 4S lipos and you can use Rubber Ring or Lipo Stripe In tpu the holder weighs 3 grams Its my first print model :) Update: New Version: FUS_Spartan_V3_LIPO_Mount_Version2.stl It's for 2, 3 and 4S...
cults3d
Antenna support for the Fus X111 Pro drone. This bracket prevents antennas from wandering during flights and allows you to lock a video transmission antenna with a female SMA connector as well as 2 protective tubes for radio antennas. The center...
thingiverse
Various bits for the fus x111. The two gopro doors depend on which mount you used. The door without the additonal bit is for the tpu mount. ...The one with the additional bit is for using the existing hero 8 legs with the bolt mount.
thingiverse
- Gopro Hero8 Mount for FUS X111 2.5" cinewhoop - 3° Degree uptilit - Almost no ducts in view in 4:3 (few pixels), no ducts in view in 16:9 / after using RS GO - Lens protector hood should be melted to the mount to make it secure. Use something like...
grabcad
i wanted to sketch a model of ford edge(2007) but kinda turned out to be some other suv...first try though...will try to do it better.
thingiverse
Customized version of http://www.thingiverse.com/thing:44484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44484 Instructions Using the following options: Logo = Ford Build_Size = 10 Build_Platform = No
thingiverse
Customized version of http://www.thingiverse.com/thing:44484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44484 Instructions Using the following options: Build_Platform = No Build_Size = 8 Logo = Ford
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 15 Font = write/orbitron.dxf stick_thickness = 3 message = Ford stick_width = 8 hole_radius = 2 flat_bottom = 1 font_thickness = 5
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=50885 Instructions Using the following options: Font = write/orbitron.dxf emboss_style = 0 icon_size = 5 icon = 6 manual_width = 107 manual_length = 181 message_one = ford hole_radius = 2.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options: font_one_size = 55 message_one = Built Ford icon = 4 icon_rotation = 0 icon_size = 12 font_two_size = 59 manual_length = 105 message_two = Tough...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: layer_height = 0.2 text_line_5 = FORD text_line_4 = text_line_3 = text_line_2 = text_line_1 = text_vertical_position = 0 text_reverse = no...
thingiverse
fus x111 hd whoop conversion, bottom case of caddx turtle v2