formbot t rex 2 3d printer

These are all of the STL Files for any 3D printed part for our T-Rex 2+ printers. I got these directly from the manufacturer. ...Hope this helps anyone like it did me! Category: 3D Printer Parts

These are all of the STL Files for any 3D printed part for our T-Rex 2+ printers. I got these directly from the manufacturer. ...Hope this helps anyone like it did me!

The mount sits on top of the t-rex and is secured by 2 bolts/t-nuts The back cover is pretty thin and needs to flex slightly in order to snap in place. Use the little lock key to make the backplate sit properly flush with the front of the case. ... I...

This is a cable chain component set intended to be printed and used for the Y-Axis of the Formbot T-Rex 2+. All files are for #8 screws and nuts (the nuts fit into components like the bed attachment nut and t-slot nut. ... Included are mounts to hold a...

Since we all know it's in bad taste to mount our spools directly to the top of a printer frame (Since it intensifies defects from vibrations), I modeled some pieces to replace the spool holders at the top of the Formbot (AKA Vivedino) T-Rex 3 (also...

These models accompany a 1/4" PE tubing filament feed setup for the Formbot T-Rex 2+. The caps are mirrored for application on the left and right extruders, and each accepts one 1/4" push-connect fitting in the top, via 1/8" NPT threads. A tapered...

Since we all know it's in bad taste to mount our spools directly to the top of a printer frame (Since it intensifies defects from vibrations), I modeled some pieces to replace the spool holders at the top of the Formbot (AKA Vivedino) T-Rex 3 (also...

Since 50mm fans like the stock ones are really hard to find in general, nevermind the right voltage and quiet, I opted to replace the whole cover and replace the 2 fans with a single 80mm. The fan I found is a Noctua NF-R8 rated at only 17dB. I...

Designed a filamentguide for my Formbot/Vivedino T-Rex printer. The mounting is very easy, just unscrew the screws from the bearings and place the guide between the bold and the frame. Sometimes i had the problem that the spool unrolls to much...

I got completely sick of the brass wire brushes on the T-Rex 2+ getting completely gunked up and decided to redesign the drip buckets to instead use a strip of silicone for wiping the nozzle. Silicone blade I'm using is here:...

Note that I do not know if all T-Rex 3's, or what Formbot machines have the SD card Slot in the Screen Control Box (I heard some 2's and 2+s do, but I cannot confirm this), or which ones that have them have active SD Card Slots. To find out one can...

... strong.... ...i will add a version with some spines but also that is ok Print Settings Printer: FORMBOT T-REX+ Rafts: Doesn't Matter Supports: Yes Resolution: 0.20 Infill: 100 Notes: i use S3D and put at 20% over for the thin wall infill nozzle 0.4

An updated print head crown for the Formbot T-Rex. This version has a small guide tube from the top to where the filament passes through the circuit board on top of the print head to make it easier to load filament. In the past I had issues where...

... printing the driving system you will have to drill and the 2mm holes to make sure they are perfectly round and at the good size. You will also need : screw M3x12 qty 2 screw M3x8 qty 8 screw M4x35 qty 2 washer M3 qty 4 washer M4 qty 2 nut M4 qty 2

A mounting system for the Keenovo Heated Bed controller used on Formbots. Longer 12mm M3 screws are required to replace the originals. ... This is the first iteration of the design which will most likely change but for now it works.

... pad (like as for chairs legs) and glued with the brake. ITA Ho creato questo freno per evitare che l'asse Z scenda con il proprio peso. Ho inserito un pezzo di feltro da 2,5mm (quelli da mettere sotto le gambe delle sedie) e incollato al freno.

... pad (like as for chairs legs) and glued with the brake. ITA Ho creato questo freno per evitare che l'asse Z scenda con il proprio peso. Ho inserito un pezzo di feltro da 2,5mm (quelli da mettere sotto le gambe delle sedie) e incollato al freno.

These are all of the STL Files for any 3D printed part for our Formbot (apparently now called Vivedino) T-Rex 3.0 printers. I got these directly from the manufacturer. ...Hope this helps anyone like it did me!

These are all of the STL Files for any 3D printed part for our Formbot (apparently now called Vivedino) T-Rex 3.0 printers. I got these directly from the manufacturer. ...Hope this helps anyone like it did me! Category: 3D Printer Parts

'T REX Formbot articulated cable tray and mount': https://www.thingiverse.com/thing:2596535 I re-mixed it as I found the CABLE MOUNT piece was not boolean'd together well and split during printing [for me at least]. ... I printed in PLA at: 0.2 layer...

'T REX Formbot articulated cable tray and mount': https://www.thingiverse.com/thing:2596535 I re-mixed it as I found the CABLE MOUNT piece was not boolean'd together well and split during printing [for me at least]. ... I printed in PLA at: 0.2 layer...

This fan adapter is necessary if you broke the original 8010 Formbot fan and you are waiting for the new one to arrive. ... This adapter id sedigned for T-rex 3 case and adapt the 5010 fan to 8010 fan holes. ...

This is a Formbot T-Rex 3 adapter for installing a BMG-M extruder with a Mosquito hotend. The original design was not fitting the BMG-M so I made some minor changes: - Changed the orientation of the twist-safe holes - Added indents for the...

This fan adapter is necessary if you broke the original 8010 Formbot fan and you are waiting for the new one to arrive. ... This adapter id sedigned for T-rex 3 case and adapt the 5010 fan to 8010 fan holes.

I had some problems with the extruder and hotend of my T-Rex printer so i decided to change to a BMG Extruder and an Dragon Hotend. For assembling, you need to take of the "old" print head. I replaced a spacer from the carriage to hold the motor...

Hi, the original silicon box is really bad, and don't allow a good cool. ...i do it with tinkercad, next version with some honeycomb holes for a better cooling.

This is a low friction solution/fix for the stock 608 bearing filament rollers. Simple fix with some spacers to spread the load and separate the 608 bearings. ...Optional, but recommended.

T Rex Head Sculpture 2 3D!Textures provided Has UV's !

Hold spools....DUH! ... ;P

Cooling duct do direct air towards the hot end.