fpv battery 3d models
83470 3d models found related to fpv battery.thingiverse
Fpv battery strap Print strap with TPU 95A Print Buckle with ABS or PETG
thingiverse
FPV Goggle Battery Holder. I designed this to hold a Turnigy 3S 3200 mAh battery. I use it to power my Skyzone 02C FPV goggles. The XT60 connector from the goggle power cable connects easily to the EC3 in the side slot which provides strain...
thingiverse
I made this bracket to accommodate my Summit's FPV system battery. ... Width: 31.50mm Length: 110mm Height: 52mm
thingiverse
UMX Timber FPV Battery Cover. Banggood VTX/ATX03 or similar. Battery slot in windscreen, maybe improved cooling too. I used a pair of 3mm magnets on each side, as that was all I had. ...
prusaprinters
This is a Holder to hold the DJI FPV 3 Batteries and Hub. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: YesResolution: 200 Infill: 20 Filament: ESUN PETG Clear Notes: This is my first posting. Category: R/C Vehicles
thingiverse
Battery holder for fpv quads with bottom location Suitable for batteries 1300-1600mah 3s, 4s, 5s and 20-25mm strap
thingiverse
Case for DJI FPV drone. ...This is so that the battery does not hit the ground when landing and taking off. ...I used double-sided tape to connect it to the drone's battery.
thingiverse
I designed this to securely hold my lipo battery in place while I fly FPV using my Headplay FPV goggles. It easily attaches to the "gopro" style mount on the back of the headset. I used supports at 10% infill with .25mm layers. ... It took less than...
thingiverse
Old battery of my Headplay FPV googles was bad. I disordered the PCB and all smd components except the 10K voltage divider resistor. Then I flipped the black connector so I could connect it when the PCB was flat in the liberator. Next the PCB was...
thingiverse
... without removing it from the case. The opening on the side allows you to check the battery charge level as well. Even if the battery feels loose in the case, once the case on the goggles the battery is very snugged and don't move at all. ...
cults3d
... the battery without removing it from the case. The opening on the side allows you to check the battery charge level as well. Even if the battery feels loose in the case, once the case on the goggles the battery is very snugged and don't move at all.
thingiverse
Because dron lands on battery, i made a little protection cover for it. ... because it slides over a cable and on bottom is secured with battery feet it does not require any glue to stay in place. ...
thingiverse
This is to hold a DJI FPV goggle battery on a 50mm headstrap. e.g. ...FatStrap
pinshape
https://www.youtube.com/Fatshark 18650 li-ion FPV battery Case with LED I finally got version 2 with led done. I kept it almost the same size as v1, I printed one and assembled it and is working perfect. So enjoy Needed components 2x li-ion battery...
thingiverse
This is a battery cover/holder for the EMAX Interceptor FPV RC car. The stock cover requires a screw to hold it in. This stays in place with friction and holds the battery securely in place. ...This facilitates faster battery changes without the need...
thingiverse
This is my take on battery caps for the 3.7/3.8v lipo batteries for the Inductrix FPV (what I have) or the tiny whoop (it's my understanding this should work too) I printed mine in Ninja Flex. Perfect fit really depends on the battery. I used some...
thingiverse
I couldn't find any (good) 18650 battery pack's for the DIY 4S li-ion pack that I wanted to make for my FPV drone for flying long range. I have used models for TPU battery protectors/caps for a 4S li-ion 21700 pack that I build before, but although...
thingiverse
Needed components 2x li-ion battery (from old laptop battery)http://www.banggood.com/2PCS-INR18650-30Q-3000mah-20A-Power-Li-ion-Battery-for-Samsung-p-1015666.html?rmmds=search Angled DC jack ID2.2mm...
pinshape
Needed components 2x li-ion battery (from old laptop battery) http://www.banggood.com/2PCS-INR18650-30Q-3000mah-20A-Power-Li-ion-Battery-for-Samsung-p-1015666.html?rmmds=search Angled DC jack ID2.2mm OD5.5...
thingiverse
I will follow up with a battery tray that features slits for velcro straps and stops that prevent the battery from slipping out. Here's the configurable battery tray: http://www.thingiverse.com/thing:1219149 The hooks will hold regular M3 hex nuts...
thingiverse
Also the use of XT60 pins which are too big was too concerning to me about damaging the battery contacts and cause later issues on the aircraft. ... This uses M3 screws (2.9mm, original connector is a 2.8mm straight pin) allowing proper insertion, and...
thingiverse
FPV Goggle Battery Tray for GAONENG 2S Lipo with 14mm x 80mm dimension.
thingiverse
FPV Goggle Battery holder I made to help keep the battery on my Skyzone 04x goggle strap. ... Not really necessary as you can learn to just be careful and not have the battery fall out but thought I'd share it still
thingiverse
DJI FPV Battery Mount. ... More information can be found viewing the following video: https://youtu.be/PMfGwEZpa5w
thingiverse
This is a Beta FPV battery clip adapter for using 2s 450mAh batteries on Meteor 65 instead of only 1s 300Ah, I designed it to print it without supports at all and to fit tight on the drone and to hold the battery firmly so that it doesn't move during...