fpv lcd 3d models
31469 3d models found related to fpv lcd.thingiverse
My FPV LCD holder and transmitter stand link: http://www.thingiverse.com/thing:349502 Instructions Print the base and hinge with 3 solid top and bottom layers, 3 perimeters and 30% fill. Use two 16mm long, 3mm filament as hinge pins. They are...
thingiverse
A simple and strong FPV LCD holder for the FrSky Taranus or Turnigy 9X. I use it for mounting my RC800, 7" LCD display. It will also hold other LCDs with back or bottom 1/4-20 mounts. I used a DIY 3S 2000mah battery pack, made of 3 18650 LiPo cells,...
thingiverse
With this stand the lcd for FPV stays more robustly to the radio. ...In my case the lcd was always spinning, just tilt the radio a little
thingiverse
Support d'écran LCD pour télécommande FlySky FS-T6 (ou autre...) Screen holder for Flysky, FPV http://fr.aliexpress.com/item/FPV-Combo-System-5-8Ghz-5-8G-200MW-Transmitter-Receiver-no-blue-HD-FPV-Monitor-900TVL/32491696264.html Print Settings Printer...
thingiverse
Spektrum sun shadefor 4.3" lcd that comes with the ready to fly RTF inductrix fpv AKA the tiny whoop Print Settings Printer: anet a2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 0 to 100 Notes: Rafts and Supports are...
thingiverse
I didn't like the cheapo Quanum FPV headset I bought, so I attached the LCD using this bracket I designed. I also made holders for the 2S 1200mAh battery I use to power it, and the 5.4GHz receiver. Yes, I know there is a commercial version...
thingiverse
I made this sun shield for my Eachine Racer FPV monitor. To customize it, just measure your monitor with a caliper and change the values. ...--- Update --- Added a rubber band clip on the bottom side to hold it better, perfect now...
thingiverse
Simple LCD screen stand oriented 20 degrees. ... LCD screen I bought : https://www.banggood.com/5_8G-48CH-4_3-Inch-LCD-480x22-169-NTSCPAL-FPV-Monitor-Auto-Search-With-OSD-Build-in-Battery-p-1364626.html
thingiverse
Nuts and bolts/mounting hardware Top piece Back piece Also includes a hinge with 3 different mounting holes so that you can fit different sized LCD monitors. Some assembly required. Here is a folding mount I made to fit a FPV monitor on a Taranis Q...
thingiverse
Recently I have started to get into the FPV craze and to go along with that I've been trying to modify my controller to mount the LCD screen. I have a fairly unique controller and limited financial backing (single income and a tight family budget)...
prusaprinters
You could also use it to mount a large antenna, such as a Yagi or Helical. Nuts and bolts/mounting hardware Top piece Back piece Also includes a hinge with 3 different mounting holes so that you can fit different sized LCD monitors. Some assembly...
thingiverse
Customized version of http://www.thingiverse.com/thing:1228343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1228343 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1228343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1228343 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1228343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1228343 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1228343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1228343
thingiverse
Customized version of http://www.thingiverse.com/thing:1228343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1228343 Instructions Using the following options:...
thingiverse
My Eachine LCD 5800D has an internal battery compartment, so it was to deep for the original measurements and I streched the thing by the mounting hole about 10.5mm to fit. It's one version solid with my measurements and one .obj file, so you can...
thingiverse
Simple cover for the Hawkeye V4 5" monitor to protect the screen & prevent the buttons getting pressed. ... Ideally should be printed in PETG, but I ran out so used PLA which seems to be okay.
thingiverse
soporte para lcd FPV radiolink AT10CH /// radiolink AT10CH Quickfit mount lcd for FPV
thingiverse
FPV googles TFT LCD 5" to 4.3" Adapter Work in progress. For more info leave comment. ... Paypal: marekjarosbrno@seznam.cz https://www.facebook.com/CNC3DFPV/ https://www.youtube.com/user/audicz/videos?view_as=subscriber
thingiverse
I wanted to improve the FPV transmitter mount I had designed for my Taranis and 4.3" LCD screen because it used too many moving parts and was clunky. I found the FPV bracket by IGI79 @ https://www.thingiverse.com/thing:703700 and wanted to...
thingiverse
A Basic sunshade for 5.6 inch FPV Monitor. Printed using 0.3mm layer height. I secured using sticky back velcro. ...
thingiverse
Simple way to convert a camera trepod to a fast to assembly ground station. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
SunShare For all FPV 7 inch Screen LCD. ...Print with Cura 14.9 layer 0.2 infill 10%
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/juOZFDmcLuQ