fractal christmas tree 3d models

Fractal Christmas tree Having made this fractal figure, I thought that it - with a little good will and Christmas mood - might well resemble a Christmas tree !? No support used, but in Cura 4.4.0 I found an Experimental feature called "Make Overhang...

2017: [Futuristic Christmas Tree](https://www.thingiverse.com/thing:2702395) 2018: [Fractal Christmas Tree (Kochmas Tree)](https://www.thingiverse.com/thing:3234168) 2019: [Hypocycloid Christmas Tree](https://www.thingiverse.com/thing:4022593) The...

... parts in wihte PLA using the spiralize setting. These tree lights were designed with a hole in the base to fit an LED light I pirated from a Christmas decoration I purchased at my local Dollar Tree (the LED shown on the table in the second photo).

SummaryWho needs to buy a Christmas Tree when you can use your 3D printer and make your own!? This tree is my own design which assembles with ease! Simply print a base then eight of the side panels and slide them together, no glue, no hassle! ...I added...

Who needs to buy a Christmas Tree when you can use your 3D printer and make your own!? This tree is my own design which assembles with ease! Simply print a base then eight of the side panels and slide them together, no glue, no hassle! I added the...

Modified the original design to accept a 55mm led light with remote. ... These lights can be found from a variety of sources and feature RGB LED lights allowing the model to be illuminated in many colors.

Great for hanging those its bitsy ornaments. Print multiple copies of the base component, with each copy being about 85% smaller than the previous. ...Connect the components with rubber bands for braces.

#Fractal Tree Ornaments This year I've designed these fractal inspired, Christmas Tree Ornaments using the Golden Ratio. I made these to give to my family and would like to share them with all of you. There are two versions included. -...

#Fractal Tree Ornaments This year I've designed these fractal inspired, Christmas Tree Ornaments using the Golden Ratio. I made these to give to my family and would like to share them with all of you. There are two versions included. The version...

2017: [Futuristic Christmas Tree](https://www.thingiverse.com/thing:2702395) 2018: [Fractal Christmas Tree (Kochmas Tree)](https://www.thingiverse.com/thing:3234168) 2019: [Hypocycloid Christmas Tree](https://www.thingiverse.com/thing:4022593) The...

2017: [Futuristic Christmas Tree](https://www.thingiverse.com/thing:2702395) 2018: [Fractal Christmas Tree (Kochmas Tree)](https://www.thingiverse.com/thing:3234168) 2019: [Hypocycloid Christmas Tree](https://www.thingiverse.com/thing:4022593) This...

2017: [Futuristic Christmas Tree](https://www.thingiverse.com/thing:2702395) 2018: [Fractal Christmas Tree (Kochmas Tree)](https://www.thingiverse.com/thing:3234168) 2019: [Hypocycloid Christmas Tree](https://www.thingiverse.com/thing:4022593) 2020:...

Fractal tree

This is a modular fractal tree that you probably need to glue together. Two basic elements are set up vertically to build the tree. With each layer, you need to use 4 cut parts and 4*i standard parts, where i=0,1,... is the index of the layer. ...The...

This was an experiment to create a simple tree using fractals and printing it on the MakerBot. The same basic unit of three arms is repeated by shrinking it in half and fitting it to the hexagonal top of the branch. ...first layer 3 branches second...

Fractal-based volumetric tree. Available in the following versions: RAW data 400x400x400 8-bit zipped PLY isosurface mesh 2M polygons STL isosurface mesh (smoothed, reduced) 990K polygons ...

This uses a similar fractal construction to my [Fractal Christmas Tree (Kochmas Tree)](https://www.thingiverse.com/thing:3234168). I tried doing this first in OpenSCAD, but I ended up creating the STL directly from Python using the numpy-stl...

This prints more nicely than my original fractal tree thing:3373. No spaghetti is produced since each layer is a continuous path. The "branches" and "leaves" are each 1.5 mm wide so they should print two strings of plastic thick. ...See thing:4787 for...

A fractal tree that I designed using OpenSCAD. Instructions Printed using green PLA with Prusa I3 Hephestos. One branch on top of the tree was badly printed but I think it was a problem with my...

... leaf width formulas, now using cones instead of cylinders for better looks. Using v2 one can create progressive complexity states of the tree, "growing" a fractal tree. ...Check [this video](https://www.youtube.com/watch?v=zswH7y-nTwA) on YouTube.

2D fractal Tree =========== This creates a **TWO DIMENSIONAL** tree that can be used in creating laser-cut designs It is possible to create a 3d extrusion of the tree using the following code: ` linear_extrude(height = 5) { trunk(); }` Based on...

Maybe it's the head cold that I have, but I just had to share this Wacky Tree Fractal. It can be used for... um... help!? I'm going to eventually get around to trying to print this. It will certainly need supports. I'll post pics and details once...

Using the same basic principle as a kaleidoscope, the four reflecting surfaces of the Christmas balls together with the three colored LEDs create a fractal pattern of reflections on the Christmas balls. So in the end it looks like a geometric pattern...

So I made this fractal tree out of 30+ redbull cans! ...   Cans you'll need: 24 x 8oz cans 6 x 12oz cans 1 x 16oz can 1 x 20oz can Connectors you'll need to print: 1 x 20-base.stl 1 x 20-16-connector.stl 1 x 16-12-split-connector.stl 2 x...

A simple fractal star that can be printed in 14 minutes and added to a string of light by either printing two and putting them back to back or using aluminum tape to hold one against the LED. Printed in both Natural PLA and the new Taulman 3D...

These trees are built using OpenSCAD. ...You can customize almost any aspect, though it will likely not print on a Lulzbot if the branch angle is too large. (The tree pictured has a branch angle of 15 and 3 layers of branching).

Modified this tree from @steveweber314 to have 5 stands for D&D Minis. Top center square is 35x35 the other 4 are 30x30. Should be enough room for any accessories you want to add. Edit** 1/23/2018** I've added the Fusion file in case anyone wants...

... .stl file for the roots. The roots and tree together are about 148 mm tall, too tall for a single print on my machine. Instructions print Fractal Tree 2 thing:4340 print Roots For Fractal Tree 2 (this thing) turn roots upside down and glue to tree

Flat Christmas tree with platform foot and pendant. The moon and star are attached with cords. ... I recommend changing the filament color to be able to appreciate details.

Pythagoras tree (fractal) 3d model 12 iterations final mesh, with overlapped uvs and Maya 2018 file for instancing cubic objects with Mash