frame for glasses 3d models
2287196 3d models found related to frame for glasses.grabcad
This is a frame for glasses with a custom design. A you can see in pictures, the colours can vary. ...The advantage of this desgin is that if you manage to break it, you can re-3d-print only the part(s) broken.
thingiverse
This is the second version of the 3D-printed frame for droplet precautions. This version comes with 2 stencils for eye shield and face shield in the .pdf file. The frame is also modified to fit glasses wearer. You may use any transparent film...
cults3d
Starting from an STL model of the left lens, build a parametric frame for your glasses. Using a hinge design by u:erickso that I further reinforced, as well as his temple design (from this thing). * * * Rev.1: adding taper to lens cutout making...
prusaprinters
Starting from an STL model of the left lens, build a parametric frame for your glasses. Using a hinge design by u:erickso that I further reinforced, as well as his temple design (from this thing).* * * Rev.1: adding taper to lens cutout making...
thingiverse
Starting from an STL model of the left lens, build a parametric frame for your glasses. Using a hinge design by u:<a href="https://www.thingiverse.com/ericsko/designs">erickso</a> that I further reinforced, as well as his temple design (from <a...
prusaprinters
... copper wire to pin the hinges, bend into the provided slots then trim flush. May need to print the frames a few times to get the right scale factor for the lenses to snap in snug but it prints fast. I print at 0.2mm layer height and no supports.
thingiverse
My frames broke so rather than spend another $300 on new frames, I decided to print a new set. ... This is designed to fit my particular lens shape but I suspect with creative use of the XYZ scale factors and maybe some hot air a lot more lenses could...
thingiverse
Eyeglasses frames for Izipizi. Frame looks a bit thick. I'm still working on it. I bent the fame and hangers after heating it up with a hairdryer. That works quite good and you get a nice front surface. ... I connected the hangers to the frame...
grabcad
I designed this frame to special requirement of a customer than needs transport fragile things. The frame have joints than fix in the holes of side walls of pick-up of a cargo van. I´ll pay atention to your comments and questions. ...All parts and...
thingiverse
ender 3 glass bed frame to keep the glass center with bed wiring strain relief and spring guides integrated into the frame. the spring guides i used are these from this link https://www.thingiverse.com/thing:4078927 an ive ran these on top of the...
prusaprinters
Put in the lenses before, the frame will shrink perfectly to them!I connected the hangers to the frame simply with tiny nuts and bolts. If the holes are not printed well enough, just drill it. ;-) Frame looks a bit thick. ...I'm still working on...
myminifactory
The Red-Cyan film-made anaglyph glasses (SG004A) are available on STEREOeYe web shop at, For No Japanese user :https://www.stereoeye.jp/shop_e/ For Japanese user :https://www.stereoeye.jp/shop/ This glasses frame isProduced by Takashi...
thingiverse
The Red-Cyan film-made anaglyph glasses (SG004A) are available on STEREOeYe web shop at, For No Japanese user : https://www.stereoeye.jp/shop_e/ For Japanese user : https://www.stereoeye.jp/shop/ This glasses frame is Produced by Takashi SEKITANI...
thingiverse
The stems came out well, but the parts of the hinges on the frames were too close together for the height of the part of the hinge on the stems, and the frames needed more help before they would hold the lenses. The third test had the added addition...
thingiverse
Frame hanger for 10mm Glass wall. Incline for stable fixation. Design Considering Expansion. ...High fixation point for minimum exposure of hanger Print Settings Printer: prusa i3 acryl version Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill:...
cults3d
Hello, here is a magnetic visor clip for my daughters magnetic frame glasses shown in her 2013 Chevey Equinox. I purchased 1/8" diameter x 1/4" long magnets from McMaster-Carr and pressed them in. ...Make sure to correctly orientate the magnets to...
thingiverse
Or if you are trying to get reading glasses for poor part of the world, this can work. The frame is big enough to hold most common size lenses, and the ear pieces can be trimmed to fit with a strong pair of scissors. The hinge rods are just a...
thingiverse
***NOTE*** When I imported this from Tinkercad to Repetier for printing i had to do some MAJOR resizing; I ended up printing it at .039 scale from the monstrosity it imported. Some post processing was necessary to get everything to cooperate; mainly...
thingiverse
Out of all the files included you will need to print: * 1 x Frames * 1 x Arms * 2 x Clip bottom * 2 x Clip nose * 2 x Clip side For assembly you will also require: * Super glue or similar * 2 x 1cm off-cuts from a paper click for the hinges *...
thingiverse
A cheap way to have cool and crazy glasses made with two 55mm Photographic Filters.
thingiverse
() If you have TWO of these glass beds you can quickly swap one bed out for the other and keep printing without your whole printer having to cool down (Tip on leveling: after you swap out one glass for another, you can still LEVEL the "new" surface...
thingiverse
This piece serves as the interface between the legs and frame of my metal/glass outdoor table. ...In addition to holding the legs, it also retains the glass.
thingiverse
It's optimized for my Aqua Medic Xenia 100 with a direct surface of 100 x 65cm, 10mm side and back glasses and a 12mm front. Due to the modular design the parts can easily be combined for other dimensions. The parts are 200 or 120mm long, so they...
thingiverse
... Landlords haven't replaced them(likely won't). So I made a quick curtain hanger for the square frame and just pulled the doors out. I printed them in 3D Fuel's Workday Black PETG. ...Nice fit over my frame, which measures 55mm tall by 50mm wide.
thingiverse
... to keep your neck from straining. Note: This part is for public domain use only and intended to help others replace their frames or share with others. ... I do not give permission for anyone to re-upload, and/or sell prints to make a profit.
thingiverse
This is a remix of D&G 3D Glasses Frames by SWFL3D. I scaled it down 83% so it would fit my 3 and 4 year old. ...I put the whole thing together so they wouldn't break easily.
thingiverse
... a glove and doesn´t hit nose or face. The dimensions of the lense and frame (picture with dimensions) should be all an optician needs to make the lenses. Just a few supports for the bridge at the frame is needed. ... Happy printing and flying...