freewing a10 3d models

The nosegear retract mount attachment for the F-14 is rather weak. The plate goes in the compartment under the canopy and 55mm M3 screws pass all the way through from the retract to better spread landing loads to the airframe. ... The block...

I need an Amraam missile model for my 70mm F-16, so I scaled the Amraam down to 1/12th size. The model is printed in three separate parts for easy assembly. Simply glue the pieces together and print it upright. ... Update (12/18): I added a mounting...

SU23 STL files are strictly limited to printing on a bed that measures precisely 200 millimeters by 200 millimeters by 180 millimeters. ...Additionally, a Pylon has been added.

If you want to use a gyro on the su-35, there is not enough space, But here is a way to help you solve the problem.

Used to craft efficient and speedy rivet lines on precision-painted miniature aircraft models, scaled at 1/5th size, with additional sizes available upon request. ...Email me directly for a quote on custom 3D printed solutions: Rockerman61@yahoo.com...

A model of the A-1 unguided rocket for the Me-262 A total of 26 need to be printed. ... The wooden supports need to be done separately (i might design it later)

The Gripen needs weight in the tail to achieve an acceptable CG position. This nozzle has accommodation for up to 60g of small lead weights, in addition to weighing over 60 grams itself. Print wide-side down, with supports. You will need to peel...

I aim to install an LED on my 70mm F16 V2 with enhanced struts, specifically designed for the upgraded aluminum front strut and a 9mm LED.

A more accurate and heavier nozzle for the F-35 V3. The existing foam nozzle plugs into the rear fuselage and is held in place with tacky glue. It is easily removed and this fits in its place. I suggest taping over the join inside the tailpipe...

Here are two gauges to make the basic control surface setup somewhat easier. ... A gauge for setting up the split rudders, 22.5 mm per side plus one to set up the Up trim of the inboard elevon.

Ersatz für die Original Teile

For a stronger nose gear, you can install this plate and use M3x55 screws instead of the original

This is one of the first parts I've made so far and its based on a few other designs for front landing gear braces on R/C planes when used around grass runways.

I design and manufacture scaled-down rivet lines specifically for use on painted foam aircraft models, typically at a 1/10th scale but also available in other sizes upon request. ...For information on pricing and to inquire about 3D printing options,...

a reciever mount for installation on top of the Avantis original controll board, no other screw needed,

This is a replica of the plywood free-wheeling T-45 90mm EDF jet steering servo mount created with 4mm resolution and 30% infill density, built without supports for optimal quality at settings two or 2.5.

an RX mount that can be installed ontop of the Avantis own controll board, now new screws needed

designed it for stronger nose leg for my turbine powered mig21, best for grass ops, FLIGHT: https://www.youtube.com/watch?v=NPNtAyuMhIw TAXI: https://youtu.be/zliW-_WyNAM print without supports, only brim, sand side facing tail if nose...

a weapons pylong that can be installed over the Avantis original wing fence

This is a semi-scale pylon to mount on the underside of the wing "cuff", where it is screwed onto the three molded-in bosses. You will need a left and right handed version. It will hold a Sparrow or AMRAAM on the vertical section and a Sidewinder...

This fits over the retract in the main gear well. Provides support for the plastic retract housing as well as the main gear strut. Right side STL is included, mirror in your slicer to create the corresponding left brace (the brace is not...

The stock F-14 uses the FLIR lens mount under the nose as a battery cooling air intake with no attempt to model the FLIR lens. This models the FLIR lens while maintaining the air intake. ...It should be a press fit into the existing intake.

Hello for the T-45! I've created a POD with pylon attached. The POD is divided into three parts: in front, you'll find a bonded section that's ready to go; behind it, there's a screw-in area waiting for its turn. Perhaps you'd like to utilize the...

I printed out two identical halves, one a perfect mirror image of the other. Next, I carefully placed a few tiny droplets of clear adhesive on each half, then swiftly pressed them together, securing them with a piece of masking tape. ...After that, I...

I've created a configuration for the T-45, incorporating a custom pylon and munition system. The bomb cradle consists of eight interconnected components, securely fastened together via adhesive bonding. ...In turn, the pylon is rigidly attached to the...

Missile is in 3 parts with a separate mounting lug compatible with the wingtip rail. ... Attach the lug to the missile body to correctly position the missile on the rail.

I copied the original rail from my F-16 since I lost one in flight. ... It's an old design done with 123D.

Hello for the T-45! I've just created a pylon and bomb set that's sure to make some noise. I used my trusty Dremel 3D40 to print out the parts, which I carefully crafted from high-quality PLA material. With Simplify3d as my go-to slicer software, I...

The design is tailored specifically for the 130A ESC, which comes equipped with a 6S stock powertrain, to enhance airflow within the intake sector.

Replaces the cheap looking foam overlay on the vectored thrust nozzle. The foam overlay is glued on with a tacky glue and with care can be pulled off intact. This is a direct replacement. Be aware that it weighs some 30g more than the foam...