front creator 3d models

not pretty but I use this to support a plexiglass for the front of my Creator X I just have a magnet holding it to the screw at the top in the center side guides will be next

This slide was designed so I could use a perspex sheet as a front cover. I used four slides to hold the cover. The holes are 3mm. It is designed to hold 3mm perspex sheets. Instructions Just use...

This is a drop-in replacement fan duct that fits the FlashForge Creator Pro and similar models that have the ‘turbo fan’ at the left of the nozzles. It has been confirmed to fit the 2015 FFCP (upwards opening door), the 2016 (sideways door), and the...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2 mm Infill: 100% Filament: rigid.ink ABS transparent Notes: This must be printed in a filament that can withstand some heat like ABS. PLA is a bad...

Used the front dual fan duct by DrLex for a couple years but kept having issues with cooling on the back side of my models I wanted a nice wrap around vented Duct for even cooling on both print heads. ///////////////// Version 1.2 started warping...

I wanted a way to mount my logitech C270 webcam to be in the front of the printer. A lot of the mounts that i saw would only work if the front door is closed. This mount works with the front door closed and open. You just need to slide the mount...

Acrylic front door 380x245x4mm acrylic sheet. Kit consists of hinge for 4 mm thick acrylic door, door handle and magnets holder. Instructions Print hinge with support. After print disconnect hinge...

Simple hinge and knob for acrylic front door for FF Creator. The hinge is designed to be glued to the Creator with poster tape and supports 0.093" acrylic sheet. The knob is also poster taped and simply rotates to lock the door. A screw is used to...

Here are some hinges I designed so that I could mount perspex covers to my Flashforge Creator. The hinges are for the front panel. The hinge pin holes are 1.75mm so you could use a bit of abs off the roll or a piece of wire. ... I will mount them with...

The manual valve is to regulate the flow. ... 100% - 80% - 60% - 40% - 20% of the section screw m2 * 8 screw m2* 10 m2*10 is glued (cyano) with FF_Creator_Pro-front_dual_duct_v6.3r p.STL https://www.youtube.com/watch?v=N721BUCsqvQ

Edit it online https://www.tinkercad.com/things/3CXUHy085bm Print Settings Printer: FlashForge Creator Pro 2016 Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 20% Notes: These are for the newer version Flashforge creator pro with the 9mm deep bed...

I made this accessory for mounting it to the front of the Flashforge Creator Pro 2016. Note that this will not fit the old style Flashforge Creator Pro which has one screw above the door. If in doubt check the part marked "main bracket" with...

... Pro. ... The original display was not compatible with the new electronics for a Diamond Hotend conversion and a new display mount was made. Here's the link for building a Diamond Flashforge Creator Pro: http://reprap.org/wiki/Duplicator_Diamond

I bought a FlashForge Creator Pro 2017 for my business and was frustrated by the hard to reach and clumsy rear spool holders. After not finding a good alternative, I decided to design my own. These spool holders attach to the printer using some of...

I added a second mounting hole and adjusted the Ducts so they line up with my FFCP..

Printer glass camera mount for Xiaomi Xiaoyi (Ants) wifi camera. It has cable guide on the inner side. ...You have to drill at least one 4mm hole in the glass to mount it.

They can bend to allow the front door to slip into the hinge holding area without removal. Print Settings Printer: QIDI Tech Rafts: ...

My tab broke off on my fan duct I initially printed out. ...I decided to add a thick ridge to the top of the tab to help strengthen this part of the duct.

This project started a year ago, after I got unsatisfied with the solution proposed with the existant cooling systems, this cooler provides HIGH air flow, with a higher distance from the build plate, so to give clearance and visibility, the idea...

Terrible dinosaur legostyle all the detached separate you can collect other models of the designer in 3d editor includes formats obj,fbx,blend

Thread creator. ...Metric.

Mage Knight Solonavi Creator.

My creator coin for my twitch fans (https://www.twitch.tv/teamz_co) hope you all enjoy it :)

This is a file generated by the Character Customizer (beta) of MyMiniFactory. ...Give it a try at the following link: www.myminifactory.com/character-creator/

Color Creator This machine makes all colors for our world – both life and dreams... Hmmm, what about creator colors? Red color increases physical energy, Green color supports balance and harmony, Blue - relaxed, at easy, calm... But this machine is...

MG I had called it a mass generator but matter creator sounds more descriptive. genrate mass. Seperation of q until mass is generated m. Placed into position print x Possible print notes, basic file. Some workings shown below. q x=q/2...

... Notes: You can make stencil with it. Overview and Background Math tool Simple polygon creator Lesson Plan and Activity Middle and High school Useful in Middle and High school.

... In this scenario, the relationship between the supposed creator of the digital model and the object being represented mirrors that of the colonizer and the colonized body, a kind of techno-scientific incarnation of Hegel’s master-slave dialectic.

http://www.thingiverse.com/apps/customizer/run?thing_id=1143325 Instructions Using the following options: bottomLetterSize = 9 baseColor = black topTextYOffset = 7 bottomLetterSpacing = 1 iconXyScale = 0.3 bottomTextYOffset = -12 iconHeight = 3...

What is OmNomNom Creator? It is a lightweight easy to use software tool to change 2D Images into 3D objects. Video: http://www.youtube.com/watch?v=GEFzczYCRu4 You can use it to create 3D Cookie Cutters, Medallions, Logos, Surface Maps, Mazes, QR...