frsky dr4 ii 3d models
21068 3d models found related to frsky dr4 ii.thingiverse
frSKY DR4-II holder to be used with zipties to hold the antennas. ...The grooves are made for the zipties to hold the angle of the antennas.
grabcad
Model of a FrSky D4R-II receiver. ...This is the first Rhino model Ihave submitted.
thingiverse
A simple mount for D4R II receiver. ...Use shrink tube or insulation tape to hold antennas to supports
thingiverse
FrSky D4R-II receiver mount to fit the Shen Drones Tweaker frame You need to flip the model 180deg to print because I'm an idiot.
thingiverse
Simple diversion antenna equipped mounting setup for your FrSky D4R-II receiver. ...You will need antenna tubes to accompany this part.
thingiverse
This case will house a FrSky D4R-II receiver and allow it to be strapped to the underside of a plate without crushing it. ...Antenna lead holes can be drilled out accept tubes to protect the leads.
thingiverse
Holder for the ZMR250 Frame and FrSky D4R-II Receiver. Fits to the front or rear. ...Print Settings Printer Brand: MakerBot Printer: ...
thingiverse
... housing for the XM receiver from FrSky with antenna supports. ...The supports simultaneously position the antennas at an angle of 90 degrees. Designed for the Martian II frame, but it may fit into other frames (holes for 5mm posts, spacing - 32mm).
thingiverse
FrSky D4R-II tray in the 36x36 format for stacking on top of similar format flight controllers (ie. Naze32, Flip, CC3D). Requires standoffs, cover or the easy print 10mm standoff tray. See the stacked modelUsage: Stack on top of FC. ...
thingiverse
The mount fits a FrSKY V8FR-II case and prints in two parts. a clip for holding the receiver in place and the main body. The design incorporates an integral clamp that locks the Servo connectors in position when the clip is fitted. for security...
thingiverse
Receiver mount for the FrSky V8R7-II. In most cases it would be easiest to just attach with double sided tape. However, I have included some mounting clip tabs which are designed to allow it to be attached to Eachine Racer 250. Simply insert the...
thingiverse
I like FrSKY receivers, but hate the lousy paper cover that the small 4-channel receivers use. They are always falling off. I printed this little case instead. I just put hook and loop tape on the bottom. ...Printer: Wanhao i3, V2 Filament: eSun PLA+...
thingiverse
Tray to hold your D4R-II in your ZMR Frame. Edit (6/7/15): Added New modified tray with VTX holder. Holds ImmersionRC 600mw 5.8ghz VTX. Also have a version to hold XT60. ... Instructions You'll need...
prusaprinters
Also have a version to hold XT60. Print instructionsCategory: R/C Vehicles Summary Tray to hold your D4R-II in your ZMR Frame. Edit (6/7/15): Added New modified tray with VTX holder. Holds ImmersionRC 600mw 5.8ghz VTX. ...Also have a version to hold...
thingiverse
Simple case with antenna safeguard for FrSky V8R4-II receiver.
thingiverse
It's been designed based on: -Naze32 FC -Matek PDB -FrSky Dr4 II -Foxeer TM25 -Runcam Swift -Liantian LED RGB -Emax RS2205 -ESC Hobbywing 30A BlHeli-S -5" Blades https://www.youtube.com/watch?v=W3NzYLZjkgk&t=282s Print Settings Printer Brand: RepRap...
thingiverse
A receiver cover for the ImmersionRC Vortex 250 and 285 and the FrSky D4R-II receiver. ...Parts needed: 2x 3mm antenna tubes 4x 6mm course thread screws
thingiverse
FrSky X8R antenna mount for Martian II. Based on the initial design of @Mauronic but the antenna lives outside of the quad frames so it's easier to install and also leave room for the battery at the end of the frame. Updated current version...
cults3d
This receiver mount allows you to use the FrSky D4R-II receiver without taking it out of the case. The version 2 Top has larger cylinders that you can drill out to 3mm and put antenna tubing in. ... Version 3 Top has sideways antenna tubes
thingiverse
Receiver mount for the FrSky D4R-II. I believe it should also work with the X4R (same external dimensions). This particular mount is designed with 30.5mm hole spacing which matches popular flight controllers such as Naze32/Flip32, CC3D, etc. Of...
thingiverse
TBS Gemini Antenna Mount, designed to work with FrSky D4R-II receiver, or other receivers with wire-lead antenna(s). There are two versions included, one with the 'WiliM' logo, and another without logo. The design goals were to: Create...
cults3d
http://www.thingiverse.com/thing:889408 I used Earthworm's great D4R-II mount, but added a little to the bottom and holes for Zip-ties. Its made to mount on the receiver tray for the ImmersionRC Vortex. ... With this box you need to take the...
thingiverse
This is a stackable holder for a D4r-II It allows mounting on any 30.5mm board such as the Naze32. CC3D, RRosd, f3 boards. Easily goes right into your board stack, great if you need somewhere light to mount it. ...The D4r is a snap fit and sits flush...
thingiverse
This is my third D4R-II holder design. This time it's designed in OpenSCAD so that you can customize many options (thickness, zip-tie locations, mounting hole width, etc.) The default settings are Naze32 mounting hole compatible so you can stack on...
thingiverse
Clip onto Hovership MHQ2 to hold down FrSky_V8FR-II Plus Receiver. I added ~3mm of foam under for cushion. ... Instructions PLA 25% .2mm layers 3 top 3 bottom 2 shell