frsky horus transmitter 3d models
7069 3d models found related to frsky horus transmitter.cults3d
Transmitter sticks with M4 tread. ...Originally created for Frsky Horus X10, but they can be used with any transmitter with M4 tread sticks. ...Treads need to be drilled by hand.
thingiverse
Tiny mount for Dragonlink on your X12s Horus. ...Print Settings Printer: Prusa i3 Supports: Yes ...
thingiverse
......Fits only on frsky horus x12s transmitter. No support needed, since it is integrated in part. Also added my printed control sticks for those who use your transmitter with tray. holes are 16,5mm in diameter, so bigger control sticks can be protected.
thingiverse
New Sticks for the Horus X12s from FrSky I didn't like the original ones. ... These are longer and thicker which suits me better You have to thread the inside with M4
thingiverse
Simple stand for the FrSky Horus, no piece of art :) For simulator use, It may be used with a 90° USB-cable plugged in. ...Print Settings Printer: CTC ...
thingiverse
... the original holder may be too big. This is smaller alternative, which makes the whole transmitter smaller to fit into case etc. ... Originaly printed on Anycubic Mega-S from PETG (PLA or ABS woul be fine too), mounted by two M3 screws from inside.
thingiverse
small stand to rise the horus for programming and when USB connector is plugged in
thingiverse
... (Used with permission). ... This thing was designed to allow the installation of a LiPo transmitter pack into the FrSky Horus X10 without any permanent modifications to the case. This project is detailed on RCGroups at the link below.
thingiverse
Gimbal protection for Frsky Horus X12S v1. Gimbal protector with hooks for elastic band v2. Gimbal protector without hooks v3. ...Seperate Left and Right Protectors.
thingiverse
This is continued series about FrSky Horus - first one is fixed handle (located here: https://www.thingiverse.com/thing:3489731 ) It's not good idea to run high-power LRS from behind transmitter, then hold it vertically, or use pigtails for antenna,...
thingiverse
Remix of pin for the FRSKY Horus X10S support / holder by hirez99(https://www.thingiverse.com/thing:2843888) Added more material to head of pin as they were quite thin and the heads would snap off if over-tightened. Designed around a M3x.05 x 25...
thingiverse
Dies ist eine aufklappbare Box für das AHL TEC Leonhardt Senderpult für die FrSky Horus X12S. Sie ist seitlich ausklappbar und arretiert beim einklappen. Benötigt werden zwei etwas längere M3x12 Schrauben zum anschrauben der Halterung, sowie ein...
thingiverse
Attached is support for the FRSKY X10S transmitter. I recently purchased the new FRSKY remote control and found that there is no support/holder suitable for this model. The grip is wider and the handle is coated with rubber, which I did not want to...
cults3d
Attached is support for the FRSKY X10S transmitter. I recently purchased the new FRSKY remote control and found that there is no support/holder suitable for this model. The grip is wider and the handle is coated with rubber, which I did not want to...
thingiverse
EXTENSION FOR SLIDER HORUS X10S-X10S EXPRESS WITH PULPIT USE
prusaprinters
Attached is support for the FRSKY X10S transmitter. I recently purchased the new FRSKY remote control and found that there is no support/holder suitable for this model. ...The grip is wider and the handle is coated with rubber, which I did not want to...
thingiverse
Remix to make these work with the FrSky Horus
thingiverse
Biohazard Gimbal protector for the FrSky Horus X12s
thingiverse
This is a enclosure for the FrSky X4RS receiver. ...The two holes in top part, are for press Bind-Button and a view to the status leds.
thingiverse
Menu-Poti for FrSky Horus X12S Printed in PLA 0,10 layer high
cults3d
Hi, Here is a FrSky Horus X12S Handle Bar for replacement of the (fragile?) original. ... Hello, Here is a handle to replace the original (fragile?) FrSky Horus X12S radio.
prusaprinters
Remix to make these work with the FrSky Horus Print instructionsCategory: R/C Vehicles Summary Remix to make these work with the FrSky Horus