frsky l9r 3d models
2242 3d models found related to frsky l9r.thingiverse
mount for Frsky L9r antenna. mounts antenna through the foam at 45 degree angle. ... printed in Abs at .2mm resolution I printed with supports, but if your tuned up well, you may not need them, max angle is 45 degrees I just glued them in place after...
thingiverse
90 degree "bunny ears" mount for FrSky L9R receiver. Stick to aircraft using hot glue or velcro or strong double sided tape. ... This version includes a slot immediately below the point where the wires exit the ears so that the wires can be embedded...
thingiverse
Glue this box in your model, and snap in the L9R. ... No glue on the L9R. Allows you to access all the ports and remove the L9R easily.
thingiverse
II needed the holder of the antenna on my Slinger Wing for the FrSky L9R receiver. ...It is applicable also and to X8R.
thingiverse
This will hold your FRSky L9R Antenna on your Recruit v2. It is much better for reception if you can have at least one antenna vertical. It has holes for mini zip ties. I would HIGHLY recommend also using double sided mounting tape. You can...
thingiverse
I Just remixed the two Objects for my foldable Xugong Travel Copter. ...Now you have the foldable Fullrangeexpirience of the L9r ;-) Have fund This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/ckjyBYq7l8a
thingiverse
I liked the original snap in mount, but I wanted something to protect all the servo connectors as well, so I boxed that area in, and created a hole from which to route the cables.
thingiverse
Remixed original thing to get better aerodynamics. The receiver antennas are just simple dipoles inside the cover, so there's no need to rotate them around the antenna axis, just 90 degrees between antennas would be enough for good signal strength. ...
cults3d
Avios Grand Tundra FrSky X8R or L9R holder rear hatch. Takes two 3mm screws. ...Glue in place.
thingiverse
Avios Grand Tundra FrSky X8R or L9R holder rear hatch. Takes two 3mm screws. ...Glue in place.
thingiverse
changes: 2015-05-15: added stronger version with 2 mm wall thickness (x8r_dual_v02_2mm.stl), use only if your printer has trouble with x8r_dual_v02.stl 2015-04-06: X8R versions also fits L9R (finally got one to check) 2014-03-17: added X6R version...
thingiverse
Model is intended to be used to mount the antenna from a FrSky X8R, X6R or L9R onto a quad. The bottom should be adhered with double sided tape. ... Instructions This piece is best printed on its...
cults3d
Motion RC Freewing F-35 V3 EDF Jet Battery tray + Frsky X8R or L9R Rec holder. ...Uses two 3x6mm screws.
thingiverse
Motion RC Freewing F-35 V3 EDF Jet Battery tray + Frsky X8R or L9R Rec holder. ...Uses two 3x6mm screws.
thingiverse
Modified Zenofex's design to add a bottom plate that fits the two screws at the back end of a TBS Discovery. ...I kept knocking the original off so wanted to attach it more securely :)
thingiverse
Made it smaller to fit my Eachine Wizard x220
thingiverse
soporte para antenas pcb de receptores frsky
thingiverse
It's free, but feel free to donate/tip if you like what you see, thank you! https://www.paypal.me/defnot4beer ~54mm tall, screw holes removed and added small pins to attach cover piece to main holder. Also modified "leg" where it stands for wider...
thingiverse
I love the orignal design, but I need it to fold so I can put the plane in the travel case. I have a folding plane, and a non folding antenna holder just won't do! Technically this was draw from scratch, but I tried to be faithful to the orignal...
thingiverse
Howdy, this is a prototype for an all-in-one lid for an antenna mount and replacement lid for the side bay on the Ritewing Mini Drak. ... The antenna mount used is this one https://www.thingiverse.com/thing:757641 and it may work out easier to print...
thingiverse
Tail mount for a FRSKY L9R receiver on the X-UAV Skysurfer. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/14DKomr2Ajk
thingiverse
A 143mm tall antenna mast to house a FrSky L9R receiver and it's antennas. Suitable for use on RC boats and rovers etc. the mast can be attached to a base by two 2.5mm screws. Print as shown (i.e. upside down) with a good sized brim to ensure...
thingiverse
UPDATE: version with antenna holder:http://www.thingiverse.com/thing:2284273 RC plane or flying-wing insert for FrSky receivers (L9R, X6R, X8R) For when swapping out different Rx from plane or wing. ...15%infill CLICK LIKE!
thingiverse
This is an antena mount for the l9r or the x8r receiver from frsky. ...It's designed to put the antennas at a 90º angle, wich is the recommended orientation.
thingiverse
SUBSCRIBE: https://goo.gl/8FiV6g L9R: https://goo.gl/UQiR7f M3 Bolt Kit 125pcs: https://goo.gl/rPFDhs 4pcs Hex Screw Drive Set: https://goo.gl/FFvVTe M3 Nylon Screw Kit : https://goo.gl/bW1KV2 https://www.youtube.com/watch?v=fyS84QSzDg8...
thingiverse
Intended for easily mounting the X8R/L9R antennas on Reptile S800 Flying Wing.
thingiverse
The L9R antenna mount is redesigned from https://www.thingiverse.com/thing:2517286 I couldn't manage to keep clips on the original mount unbreakable. So redesigned it to have cylinder, that stiff inside the hole firmly. I also added 3mm deep cavity...
thingiverse
Reciever mount for the spidex pro. ...Matches frsky l9r reciever but probobly fit alot more. ...Mounts on the back inbetween the batterytray and the main frame
thingiverse
Antenna mount for FrSky X8R receiver. ... EDIT: Added L9R version (usable for X8R too)
thingiverse
I loved the quadcopter TX keychain by Mike-vorn-Mars (https://www.thingiverse.com/thing:2548116), but wanted an FrSky inspired version: This is a stylised Horus, X10 or Q7... you decide. It's designed to be printed as four pieces, 1 x TX, 1 x...