frsky r9 mini 3d models
91736 3d models found related to frsky r9 mini.thingiverse
30.5x30.5mm, integrated pod for 28x20x8mm VTX, full sized camera and FrSky R9 mini. The antenna mast is vertical for optimal gain pattern. ... VTX is enclosed for protection but watch out for heat build up.
thingiverse
Print with TPU then insert the R9 mini into the hole.
thingiverse
r9 mini reciever holder for johnnyfpv 3 inch frame, oh, beautiful~~
thingiverse
I made a remix of the Immortal-T-Antenna mount for the Acrobrat frame to fit the Frsky R9 mini T-Antenna. ... All kudos to pathfinderzero for the initial design.
thingiverse
Antenna mount for the Frsky R9 mini T-Antenna to fit the Chameleon frame or other 30.5x30.5mm stacks.
thingiverse
Shield mount for Frsky R9 mini and TBS Crossfire stock antenna. **2019-01-06** Thicker version with a larger hole. ... Print in TPU 95-98A
thingiverse
FRsky R9 mini and VTX mount for GEPRC GEP-VX5. ...Also you can use it for 2.4GHz (see pictures)
thingiverse
Simple mount for one or two FrSky R9mm / R9 mini receivers for GepRC LC7 "Crocodile" frame. ...
thingiverse
A simple 'hammock' to hold a FrSky R9 Mini/R9MM receiver (or similar) between the standoffs of a Super G Plus. I mount the receiver by putting a piece of heatshrink around the whole receiver + hammock. ... Print in TPU with 100% infill.
thingiverse
This is a mount for Marmotte to secure the TBS Unify Race 2 VTX, Frsky R9 Mini RX and Immortal-T antenna in place. ...Print with TPU 95A or 98A to have enough solid mount, but flexible enough to fit the antenna.
thingiverse
Hard case cover for Frsky R9 Slim+ You will need to print: 2x Tube 2x Tube_extension 1x main-shell *Optional 6x Tube_cap
cults3d
I designed this to hold the R9 Antenna in my planes. They can be glued or screwed to the sides of the planes or wherever they need to be held. Stops them flapping in the wind and you can place the antenna in the correct position knowing they should...
thingiverse
I designed this to hold the R9 Antenna in my planes. They can be glued or screwed to the sides of the planes or wherever they need to be held. Stops them flapping in the wind and you can place the antenna in the correct position knowing they should...
thingiverse
Holder for FrSky R9 wire antennas (not "T" !) for receivers like R9 MM/Mini (OTA). Design used for 7" free style frame, thus, height of part with 5 m hole (for frame standoff) may vary. ... Made for antennas like:...
thingiverse
Handle to antenna FrSky R9 RX for Cinewhoop/Cineboy
thingiverse
Cad file @ https://bit.ly/2Lo5aBA This will make your FrSky R9 antenna look and feel like an immortal T. ... The parts are symmetrical so print 2
thingiverse
FrSky Antenna holder for Immortal R9 the holder is designed for the fuselage or the wing in the aircraft Printed from PETG Tested on people :)
thingiverse
ABS Plastic No support 100 % Temp for my plastic 245 / 105 frsky r9 ver 2 small scotch.STL tower 15.5mm small scotch standart 17mm BIGER scotch 3m
thingiverse
FrSky R9 internal cover for X9e. The standard module does not fit in the body and therefore I made the cover for this part. ... Made from PLA Replaces the original cover
thingiverse
This is another in my FrSky Receiver series, this is to hold the FrSky R9 Stab Receiver in place whilst I calibrate it, the connecting wires or antenna are held out of the way so I can move it in all six directions needed whilst calibrating. Then it...
thingiverse
Extended Frsky R9 / TBS Immortal T antenna mount for iFlight Nazgul5, XL5 quadcopter. With this antenna mount the antenna is located at a greater distance from the carbon fibre frame and thus you get better/more consistent RC link/RSSI. ... 65%...
thingiverse
An antenna holder for my long range fixed wing plane to hold FrSky R9 receivers tape antennas in 90 degree angle for bet performance. ...After mounting may ad holder for receiver itself to be mounter inside at the bottom of the wire-through pin.
thingiverse
This is another in my FrSky Receiver series, this is to hold the FrSky R9 Stab Receiver in place with my model aircraft. I glue/screw this into the position in the plane I want and after I have calibrated the receiver, I then place it in this cradle...
thingiverse
Immortal Antena R9 Frsky front mount for BR30
thingiverse
Frsky R9 T antenna mount for Tina Whoop Material: TPU