frsky x4r 3d models

Porta ricevente FrSky X4R

Hi, Here's case for Frsky X4R-SB, which fits on Diatone ET160. Can be stacked also over Naze32 or other FC's with screw holes on 30,5mm pitch. 8mm M3 stand off's or normal M3 nuts can be used for fixing. Added another print also, in case longer...

Another FrSky X4R support, that can fold to front and back. The pivot's hole is threaded for M3. You will have to finish using a metal screw before trying a nylon one. Design, made with Fusion 360, is mostly parametric and can easily be modified. If...

This is a super simple mounting plate for a FrSky X4R receiver for drones. I sized it to fit the common pattern with 30.5mm between each corner mounting hole. I use it on top of a stack consisting of Lumenier LUX v2 flight controller...

Soporte para el receptor Frsky X4R con montaje para antena de diametro 3mm. ...La distancia entre los centros de los agujeros es de 30,5mm.

Low Weight, low space 30.5mm support for Frsky X4R receiver. Easy access binding switch and LED, Two holes for antennas. Perfect fit and hold of the X4R, a little hard to fit the first time (easy with TPU) in case of difficulties crack-off the last...

... model. One thing which is lacking, which I don't know if it is a problem or not yet, is the lack of bracing underneath the antennas. From what I know, this model is compatible with: x4r, x4r-sb, d4r-ii How I Designed This Designed in FreeCAD v0.16

The case is designed to allow the paper covered X4R radio to slide into place. To prevent the radio from slipping out, a cutout in the bottom of the case allows securing a piece of mounting tape or something less than 2 mm deep to be taped or glued...

FrSky X4R receiver case w/button. Material to make top: SBS, Neylon (PA),Petg. ... Material to make case: any.

Little Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. ... No Support needed.

SummaryLittle Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. ...No Support needed.Print SettingsRafts: Doesn't MatterSupports: NoResolution: 200Infill: 10Notes: Mine is...

This will allow you to stack a FrSky X4r or D4rII RX on top of a TrampHV VTX. The receiver holder stacks on top and there are plenty of zip tie possibilities This thing was made with Tinkercad. ...Edit it online...

A 2 piece hard case for FrSky X4R receivers. Enables the use of double sided tape or velcro to fix to the model. Offers some protection in the event of a crash. The case weighs 6 grams in total. Printed in PLA at 0.2mm layer height. ... Use M3 x 6mm...

Little Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. No Support needed. ...Print Settings Rafts: Doesn't Matter ...

I had an incident caused by the antenna plug coming loose. This case prevents that happening. As it replaces the cardboard cover the final dimension as about the same. Because the case is thin, I recommend printing it at 0.1 layer height. ...

This case covers up nearly the whole receiver including the pins. ... I usually use hot glue near the pins to keep the receiver in the case and then stick it to the chassis using 3M double-sided tape.

Simple receiver mount with cap, 30.5x30.5 mounting holes, just glue cap after installing. Stackable with my cc3d case. ...Print Settings Printer Brand: Wanhao ...

FrSky X4R receiver case w/button (pinless version). Material to make top: SBS, Neylon (PA),Petg. ... Material to make case: any.

Simple part to cover unused pins of X4R receiver when using S-Bus to help prevent shorting. ... Recommended printing in TPU Print Settings Printer: Prusa i3 ...

This is a simple mount for the FrSky X4R-SB receiver fitting on a RCExplorer MiniTricopter Print Settings Printer Brand: RepRap Printer: BQ Prusa i3 Hephestos Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 50 Notes: Printed in PLA,...

Built specifically for the Frsky X4R-SB (and similar) & Flight Controllers with 30.5mm hole spacing like the Naze32 or SP Racing F3 Flight Controller. Screw down with 2mm hex screws. Use coffee straws for antenna tubes to get a perfect 90 degree...

This is an antenna mount designed to suit the Frsky D4R and X4R range of receivers. (however it can be used with any receiver that uses long antennas... Futaba/Lemon etc). I mount my X4Rsb in between the frames. The antennas push through the frame...

- RunCam Split or Mini, different tilt options including "set-your-tilt" by mounting two screws inside and one to the front rail. ... - Naked X4R zip tie mount at base (or other pinless RX) - Eachine VTX03 mount - LED panel mount updated: 12/2/17

Not happy with the existing holders, I designed this myself to be used with X4R and D4R-II receivers. Its a tight fit so the cardboard cover must be removed. The label can be stuck on top for easy identification of the connectors. The antenna routing...

Enclosure for a naked X4R-SB receiver made to accompany Receiver Antenna Protection Tube with outside diameter of ~3.10mm and inside diameter of ~1.5mm. The lid can be mounted by inserting two m3 nylon hex nuts in the back of the case and fasten...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/kvm4sgZNg43

Simple holder for Frsky d4r or x4r style receivers intended to stack on top of a flight controller. ...The RX holder will need to be printed with supports, I suggest the Interface support in the newer cura 3.2.1

Yet another Receiver holder that fits for Frsky D4R-II and X4R-Receivers snuggly. The actual antenna part can be tilted for easy transportation. The swivel-mechanism also helps in case of a crash. Fits both on my vortex 285 and vortex 250 pro. Most...

Simple and slim case for FrSky X4R (sb) receiver, cover is mounted with 2 small screws, holes for connectors and LEDs and information . ...