frsky x8r 3d models
2320 3d models found related to frsky x8r.thingiverse
I made FrSKY X8R receiver antena holder to screw detween botom plates for QAV250 frame
thingiverse
Just a simple 3mm screw mount for the FrSky X8R Antenna. ... Instructions Requires supports, print at 0.1mm with 100% infill.
thingiverse
A simple Frsky X8r style antenna holder in two pieces. ...Print in flexible or normal filament
thingiverse
FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...
cults3d
FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...
thingiverse
Universal X8R mount, 45x45 mm 2.5 mm mounting holes Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 30%
thingiverse
Frsky X8R antenna mount that clip to the frame of the drones. ...Tested for Tarot 680 Pro, Tarot 650, F450 & 550 frames
thingiverse
Holds the antenna of the [X8R Receiver](https://www.banggood.com/FrSky-X8R-2_4G-8CH-SBUS-Smart-Port-Telemetry-Receiver-p-79386.html?p=P818016937014201610N) at 90 degree angle for better signal quality.
thingiverse
This is a holder for the Antennas on the older Frsky X8R receiver. The X8R just fits under the canopy and this holder keeps the orientation correct and keeps them away from the props. Depending on shrinkage/expansion you may need to open up the holes...
thingiverse
FrSky X8R antenna mount for Martian II. Based on the initial design of @Mauronic but the antenna lives outside of the quad frames so it's easier to install and also leave room for the battery at the end of the frame. Updated current version...
thingiverse
This is a hinged antenna holder for the Frsky X8R: http://www.bcmultirotors.com/#!/Taranis-X8R-8-16CH-Telemetry-Receiver/p/35032157/category=13277089 I made it to go on the BC Chipmunk 170 frame:...
thingiverse
This will hold your FRSky X8R Antenna on your Recruit v2. It is much better for reception if you can have at least one antenna vertical. It has holes for mini zip ties. I would HIGHLY recommend also using double sided mounting tape. You can...
thingiverse
This is an antennas holder for FrSky receivers X8R/X6R with pcb style terminals. Keeps the antennas in 90° position. It's possible to position it in standing or laying position inside the model, with a small piece od double tape even on top of the...
thingiverse
I needed to mount my FrSky X8R receiver on the S500 quadcopter frame. I wanted to mount the antennas to the arms but then thought the ESC's might cause range problems. So i decide to put the antennas on the bottom plate and pointing outside. One flat...
thingiverse
This is a foldable antennas holder for the x8r. You can put this thing vertical an also horizontal for storage. In a crash, the antennas will fold instead of breaking. ...To make this thing, you will need a little bit of hot glue to hold the pieces...
thingiverse
Customised version of the upright X8R mount by https://www.thingiverse.com/thing:863785 Designed to fit the Tarot 680 Pro frame, It slots over the back canopy pin and can be held down with either tape, a rubber grommet or even 3M double sided tape.
cults3d
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/4FstEYgfpwt The V2 model is a little heavier walled. ...The wire runs are a little longer too so if your antenna wire is already tight that be a problem.
pinshape
SummaryThe hi3 is my final version of it and it fit the http://www.thingiverse.com/make:70346 :-D
thingiverse
Receiver holder to fit in your R/C models. ... Antennas angle @ 90 Deg.
thingiverse
The hi3 is my final version of it and it fit the http://www.thingiverse.com/make:70346 :-D
thingiverse
Made this to hold receiver. Printed with no supports. ... Glued to Balsa airplane and receiver will snap in and out.
thingiverse
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/4FstEYgfpwt The V2 model is a little heavier walled. The wire runs are a little longer too so if your antenna wire is already tight that be a problem. ...
thingiverse
FrSky X8R Halter inkl. ...Antennenhalter zur Montage an Tarot 680