frsky xm plus receiver 3d models

This is a mount for the FrSky XM+ receiver. I wanted the antenna orientation to be in the straight up and out the back angles on my QAV-XS. I called it aft and dorsal. I also added a hole for zip tie mounting through the main body. BTW TPU is my...

Cases for the FrSky XM and XM Plus receivers to provide a little more protection than the clear shrink-wrap that is installed from the factory. This is a simple two piece case which allows access to the BIND button and connections. I'm using the XM...

Cases for the FrSky XM and XM Plus receivers to provide a little more protection than the clear shrink-wrap that is installed from the factory. This is a simple two piece case which allows access to the BIND button and connections. I'm using the XM...

Its a case with top for the frsky xm+ receiver

This allows the Frsky XM Plus receiver to be attached directly to the Flite Test Aura Lite Gyro System.

So this is a mount for the FrSky XM Plus receiver. It's meant to be mounted on a 30.5 x 30.5mm stack (The size used for 5" builds.. So, the regular size) Use a zip-tie to secure the receiver to the mount (I'm sure hot glue would work too, but it's...

This allows the Frsky XM Plus receiver to be attached directly to the Flite Test Aura Lite Gyro System. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: NoResolution: 0.15 mm Infill: 15% Filament: Hatchbox PLA Category: R/C...

Simple case for the XM+ with right-angle pins. It fits well, but I used a drop of CA on one of the edges. ...You can still get to the bind button and antenna leads.

These are folding TPU holders for the FrSky XM+ receiver, with a hole for easy access to the binding button (yeah my button is missing its top) and reusable to make it easier to replace or move to another quad. In 4 different variants: Plain...

(this is a re-upload because Thingiverse is quite broken, the first upload doesn't appear in searches or even my own designs collection) These are folding TPU holders for the FrSky XM+ receiver, with a hole for easy access to the binding button (yeah...

case for frsky xm+ receiver for flight test ft 210 frame

Plate for FrSky XM + Receiver (SBUS 16 channels) (EU-LBT) and antenna guide

This is designed for mounting XM+ receivcer in 20x20 slots. ...The antenna(s) could be hold as the receiver is pluged in.

A simple bracket to mount a D16 XM+ micro receiver to your drone. This bracket is a press fit and may require some hot glue or a zip tie to firmly secure the receiver. Made to fit 19.5mm x 19.5mm bolt pattern. ...Originally I designed this for the rear...

Simple 2 part case for the FrSky Archer M+ receiver. ...I used Welder, a flexible and removable glue, to tack the case halves together and provide strain relief for the wires.

Customizable model ! ... FrSky XM+ (XM Plus) holder. Mount holes 20x20. ...Need some postprinting cleanup, but hold receiver very strong.

Frsky Xm+ receiver holder. ...20x20-3mm holes for micro drones.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/c1FFBNP8ABU It is remix of thing: https://www.thingiverse.com/thing:2301216

Hi there, Here's a bottom plate for Tyro89 I made, it holds an Frsky XM+ receiver Juste grind a little bit the XM+ support with sandpaper (just a little) to adjust the pressure on the receiver Made in PLA

... allows you to mount the receiver as part of a stack, so that it is super neat. ...Has holes for a zip tie to secure it if you'd like. XM+ purchased here: https://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html

This mount uses the frontal top part of the X220S to mount a FrSky XM+ with its two antennas using small cable ties and heatshrink tubing. You will need four 9 mm M3 screws to replace the stock ones (6 mm). The receiver PCB itself is mounted also...

This allows a FrSky XM+ to be mounted in a 20x20 mm stack. ...Print with TPU.

I made this case for the Frsky XM+ reciever, I have used some clear tape.to hold the lit on This case is tested and will fit 100% for sure. If you print just one case, go slow and get a good cooling down, the case is tiny. ... Happy printing !

Simple Half Stack for the XM+. Use double sided tape and heat shrink for a lasting hold. ... **Updated with a new version that is smaller and thinner.

Clip onto Hovership MHQ2 to hold down FrSky_V8FR-II Plus Receiver. I added ~3mm of foam under for cushion. ... Instructions PLA 25% .2mm layers 3 top 3 bottom 2 shell

Receiver mount FrSky XM+. ...Hole Distance of Installation: 30*30mm

puda x5 frsky XM + cover

This is an ABS holder for the FrSky XM receiver, has slots for a small zip tie but not needed. The XM slides right in and you can solder on the 90 degree 3 pin and cut short so it barely pokes out the bottom. ...Print in ABS 75-80% infill.

FrSky XM mount for 20x20 or 16x16 builds. ... 3mm arm thickness or 2mm arm thickness.

Simple housing for the XM receiver from FrSky with antenna supports. The supports simultaneously position the antennas at an angle of 90 degrees. ...Designed for the Martian II frame, but it may fit into other frames (holes for 5mm posts, spacing -...