fs20z 1 smartthings 3d models

A remix of the SmartThings Hub (Gen2) Wall Mount - Ports on Bottom by neonpolaris. When I sliced the model in S3D it was two objects and the print would have been very weak structurally. ...I repaired the model so it is only one piece now.</p> ...

I reverse-engineered the original support (smartthings_MP.stl), then extruded the base by 5mm (smartthings_MP_5mm.stl), and finally extruded it again by 5mm to reach 1cm (smartthings_MP_1cm.stl). [Update 2/28/2017: I've added a stackable 1cm...

This is a 3D printed housing for the SmartThings Motion Sensor (2015) designed to replace the single CR2450 button cell battery with two AAA batteries, providing significantly increased energy capacity of over 2000 mAh compared to the ~600 mAh of the...

After designing the SmartThings multipurpose sensor 2015 and 2016 models and successfully operating all my motion sensors with AAA batteries, it only made sense to do the same with the SmartThings multipurpose sensors, of which I have a larger...

I use the Samsung Smartthings Tracker on my dog's collar, attached with a keychain mount that provides real-time GPS tracking at an affordable price. The tracker is secured in place by a small lip near the top of the mount, which prevents it from...

I use a keychain mount for my Samsung Smartthings Tracker, attaching it securely to my dog's collar. This affordable real-time GPS solution provides reliable location tracking for your pet at an unbeatable price. For optimal results with this...

This is a remix/upgrade of my original design at https://www.thingiverse.com/thing:4736820 This design has been updated to version 1.4. This will likely be my final revision as the design seems fairly robust now, and this is a low-touch fixture for...

Replacement Part for Smarthings Motion Sensor 2015 Print Settings Printer: MP Select mini Rafts: No Supports: Yes Notes: The replacement part requires support for the bottom plate and side grip. ...Upcoming updates will add tilt capabilities to the...

A Simple yet Effective Solution for Smart Lighting Control! Or Anything Else You Need a Wall Button For. I leveraged existing designs for wall plates and smart buttons to save time - a huge thanks goes out to icefreez, whose model I modified and...

Slight modifications to the original to fix some off-center features and provide a STEP file.

I designed this mount so I can temporarily mount the multipurpose sensor as a way to bypass the (semi) permanent 2 face tape. If you are using this on the inside of a door jam and there is no space to mount the smaller half of the contact sensor you...

Publishing my outdoor housing, I utilize it on the entrance of my backyard garden door. Two holes allow me to screw it securely onto the door. The door is designed to snap into place, and I recommend taping it firmly so that no water can penetrate.

This is a remix of https://www.thingiverse.com/thing:3284772 for those who'd like the 3-button option.

This is a remix of https://www.thingiverse.com/thing:3284772 for those who'd like the 3-button option. ...

I adapted cmar's design to reduce print material and ensure the status light is visible from below. This version prints vertically without supports. It mounts securely to the wall using three screws, making it perfect for high locations where only...

The device clicks into place once printed, requiring only a few minutes of assembly time. ...To secure it firmly against the wall, I opted for industrial-grade mounting tape, which also enabled me to swiftly attach the sensor component.

I adjusted the magnet holders so that the opening faces the wall plate, resulting in a cleaner appearance when the button is not installed. The absence of the button reveals a white disk and eliminates the problem of magnets being pulled out of their...

I tweaked cmar's design to give the mount a sleek new look by flipping the ports so they face downwards. My hub was super snug in the original, so I beefed up the width and depth of the opening for the hub by 1mm. It still fits like a glove, but not...

A quick hack to allow mounting @JellyTitan's minimalist Hub v2 mount 90 degrees so I could put it between two wall studs in this unfinished hallway. ... Source docs:...

Papaslights posted a great hub mount from which this was remixed. I really liked the design, but it was too large to print on my Monoprice Mini Delta, so I decided to chop it up so it would fit. This is my second iteration (the first had 4...

This is a remix of the excellent shrunken down remix of superdave4444's (https://www.thingiverse.com/superdave4444/about) remix (https://www.thingiverse.com/thing:2739611). I liked how little material this one used because the tall back panel was...

I took the outstanding shrunk down remix of superdave4444's remix and made some tweaks to fit my needs. I liked how little material was used in this one, as the tall back panel was removed from the original design. ...However, I wanted cables to run...

1

1

1

1

1

1

1