ft 5 3d models

This is a conversation for the Folgertech ft-5 making it into a corexy. ...By me- William Puchot How I Designed This Autodesk inventor

just an ft-5 idler

Uses 19 mm dowels for spool holder above the FolgerTech FT-5

This is a 2020 spool holder. ...Design is a first draft so might be some changes soon. i3 or FT-5 or even Kossel!!

glass clips for the FT-5 printer This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0LrqYZuqpvj

This is a filament guide for my FolgerTech FT-5, it prevent the filament to hit the chain rail, i use it with an other filament guide, created by Joe Mike terranellahttp://www.thingiverse.com/jterranella How I Designed This

... the bottom of the TUSH. I mounted it on the front of the FT-5 for better feed to the extruder, but you could clip it anywhere along the 2020 frame. ...You will need to print 4 of these and it also will require qty:4 - 608 bearings for the rollers.

this is a slight mod of DuMonYu, FT-5 fang hope this is ok with you as i was asked for the mod file from the photo i posted. the slight mod is iv just moved the left fang closer to the hotend. ...i printed this flat as in the photo of them both Using...

This will mount on the top side rails, left and right of the FT-5 and is 150mm high so the spools should be in a perfect height, Mount one on each side center of tower at center of rail. I made the mounting holes so you can use 4 of the leftover...

I had it mounted between 2 brackets on the Folgertech FT-5 and the spool kept catching on bolt heads. I designed this with a fence on it to keep it away from the bolts. Any spool measuring less than 81 mm wide will fit this spool holder. Update...

Didn't care for the stock spool holder on the FT-5, so I made a better one. Fits standard 2020 extrusions. You'll need a 1-1/8" (28mm) diameter PVC pipe. A slightly smaller pipe will work, if you use epoxy or hot glue to hold it in. Note: you'll...

Filament guide for FT-5. These allow you to run a bowden tube before the extruder to prevent filament snags, it also ensures even pull on the filament no matter the position/movement of the extruder. There are two versions, one is chamfered at the...

Folgertech FT-5 Custom Parts This is a collection of custom designed parts I have created to replace parts on my Folgertech FT-5; most were modifications on the existing parts that I created using SketchUp. Y-motor and y-pulley mounts Replace parts...

This is 2nd CoreXY conversion on my FT-5 R1. All the parts are printed with PETG on the Original Prusa I3 MK3. M3 assortment set will be good to assemble them. Also, M5 10mm bolt and hammer nut are required to attach on the 20x20 aluminum extrusion.

... Y inertia and will in no way hurt or damage your printer in any way. Print Settings Printer: Folger Tech FT-5 Rafts: No Supports: Yes Resolution: .3 Infill: 40% Post-Printing File the 2020 slot a little to fit. ... Tell us more...

This is spool holder 608 bearing mount that can be used on the FT-5 when using https://www.thingiverse.com/thing:2414257 as a top frame on the printer. It requires 4 608 bearings and nuts and bolts to mount the bearings. One of the nicest things...

Cooling fan for a Folgertech FT-5

Folgertechn FT-5 spool holder for printer, cutter, saw

Bowden mount with BL touch for FT-5

FT-5 spool mount Use 18mm diameter wood or plastic dowels through hole.CLICK LIKE!

Original, Stronger, and Dual Spool mounts for Folgertechs FT-5 3D printer.

these are the pieces I used to make my new Ft-5 bed

Filament mount for a Folgertech FT-5. ...Re-uses the 8020 bar from the front of the machine.

Layer fan for my Prometheus V2 mount on the FT-5. ... https://www.thingiverse.com/thing:2543862

I wanted a strong, light E3d carriage for my FT-5 so here it is. its basic and it works. ...

... OD PTFE tubing. Works with 20mm 80/20 extrusion. Holes are for M5 socket head cap screws. Works well with my other design: http://www.thingiverse.com/thing:1982717 Print Settings Printer: FT-5 Rafts: No Supports: No Resolution: .3 mm Infill: 10-20%

... OD PTFE tubing. Works with 20mm 80/20 extrusion. Holes are for M5 socket head cap screws. Works well with my other design: http://www.thingiverse.com/thing:1982717 Print Settings Printer: FT-5 Rafts: No Supports: No Resolution: .3 mm Infill: 10-20%

This is a remix of my other design ProStruder Dual Cooler (https://www.thingiverse.com/thing:2636707) for the FT-5 version of the ProStruder Dual Mount (https://www.thingiverse.com/thing:2498096).

This is a side mount for my FT-5 3D RepRap Full Graphics LCD Swivel Case(https://www.thingiverse.com/thing:2141320). ... **NEW VERSION https://www.thingiverse.com/thing:3076209**

This is an improved endstop for the FolgerTech FT-5. ...Using two bolts to secure it instead of one provides much more clamping force, preventing it from sliding up or down the rod.