ft print 3d models
1204516 3d models found related to ft print.thingiverse
This is a FT Arrow Fuselage based on its original design. ...It is enlarged in width to 2" to accommodate larger battery and flight gear.
thingiverse
Customized version of http://www.thingiverse.com/thing:215386 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=215386 Instructions Using the following options: thick =...
thingiverse
Units: inches Print each half flat side on bed of printer. Note orientation of motor mount plate (half circle to the top). Position of Mount Plate is dependent on whether you are running the "B" or "C" pack from Flite Test. Assemble then glue...
thingiverse
N Scale 3 ft X 8 ft concrete culverts that can be printed as standalone objects or used on top of the switch machine. I'd recommend that you also look at further information and pictures on how they can be used here.... ...
thingiverse
Rough draft of the FT A-10 ply parts reworked for 3D Printing. Full information on plane here https://forum.flitetest.com/index.php?threads/unofficial-ft-a-10-warthog.57108/ Use a stiff material. PLA should work. ... PET-G is better for motor mount
thingiverse
Remixed from http://www.thingiverse.com/thing:661096, I just added a 2mm wall and floor :) Total Length are 50mm end to end Update 22/01/2016 printed and tested it with my AXN cloudfly motor (not a mini motor :D), will see how it fit on the plane...
thingiverse
This is my 3d print friendly version of the Flite test FT-pun jut Firewall. ...I have built the pun jet from the plans and wanted to print the firewall so I can finish it off.
thingiverse
All that is needed to complete one half the landing gear is the 3d printed parts with 3 pieces of 4mm carbon fibre that is 118mm, 100mm and 125mm long and a piece of m4 threaded rod to fit the shock on. ...I put a piece of 5mm balsa inside the fuselage,...
thingiverse
... broke too easily. Print Settings Printer: MakerFarm I3v 8 Rafts: No Supports: No Notes: Print the tallest layers you can for best strength. ...How I Designed This Imported original STL into sketchup, revised, exported stl, netfabb online repair.
thingiverse
For use in FT mighty minis. ...2 degree thrust offset.
thingiverse
Simple mount, just print and use. ...Note: This is for the 3/8" wider pod by dayve ( http://forum.flitetest.com/showthread.php?24402-FT-Mini-Arrow/page9 ) when cutting your wing, leave 3/16" on each side and it will fit perfect. ...Have Fun!
thingiverse
... them out yet. Print material can be pla or abs, I recommend carbon fiber pla or abs especially for the shortened versions. Use 100 percent infill to ensure strength. ...You will also need 8X m3 nuts to use to mount like in the pictures provided.
thingiverse
UPDATE: 08/19/2018 - uploaded a corrected stl_Firewall_Mount_Plate.stl file, slots for mounting motor were off slightly. Units: inches Glue together with CA glue. ... I assemble the unit and tape it with masking tape then glue.
thingiverse
Made a "Wood Box" for the Dr!ft RCs. ... Print it in Wood Filament and enjoy your new Dr!ft Wood Box. ... In the file section there are a normal Wood Box also.
thingiverse
HO scale 9 ft. ...staircase. Prints at 0.2 without supports.
thingiverse
This is a kit to help with the noise in the parts in Ft-6 prints The problem I ran into is that the Two motor breakout board for X axis seems to backfeed power between the two motors and adds noise in the print and limits the speed This can cause you...
prusaprinters
This is a kit to help with the noise in the parts in Ft-6 prints The problem I ran into is that the Two motor breakout board for X axis seems to backfeed power between the two motors and adds noise in the print and limits the speed This can cause you...
myminifactory
This is a gremlin pod designed specifically for the FT Gremlin micro quad. PLEASE PLEASE PLEASE TAKE PICTURES IF YOU PRINT ONE! Tips are always loved and available on my profile, but certainly not required. ...Happy flying!
thingiverse
• Print face down for best results (The STL file is upside down for display purposes but can easily be flipped 180° in your slicer). • Use supports at the four recessed mounting screw locations to provide a nice surface for the screws to...
cults3d
• Print face down for best results (The STL file is upside down for display purposes but can easily be flipped 180° in your slicer). • Use supports at the four recessed mounting screw locations to provide a nice surface for the screws to tighten...
thingiverse
... ...It's about twice as thick compared to one made out of hobby plywood Print it how you like/ to your specific printer settings. I have just added what my settings were. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 90%
thingiverse
Simple retractable Stand for the FT-817, FT-818 Radio. ...Nut should be selfsecuring or use Locti** (no advertising)
thingiverse
Just drawed some parts to make the ft explorer easier to build, and make it more rigid when building with depron 6mm.
sketchfab
Renault FT, a french tank of WW1, i made the low poly model and unwrapped UVs on Maya 2016. ...The pbr textures created on Substance Painter 2.
sketchfab
As part of the Alexandria, VA 18th Century Ship Project, we are laser scanning each individual timber in high-definition and creating 3D models, which we will use to reconstruct the ship. ...This is timber FT 22, the first futtock for frame 22.
sketchfab
As part of the Alexandria, VA 18th Century Ship Project, we are laser scanning each individual timber in high-definition and creating 3D models, which we will use to reconstruct the ship. ...This is timber FT 7, the first futtock for frame 7.