ftc rev driver hub 3d models

This case houses and protects the REV Drive Hub utilized in the First Robotics FTC competition. ...An opening has been added to expose the speaker and tabs added to lock the device in place.

A case to store your REV Robotics Driver Hub. ...Many customization parts are included, as well as a blank base and cover to customize yourself.

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

I designed and printed this after a student tripped on a cord attached to my driver hub. Unfortunately if fell and no longer works properly. ... I printed this with 3 layers of TPU and 30% infill to get good shock characteristics but still stay...

This is a case for the new rev robotics driver hub. All I/O is accessible. There are holes on the back to match those on the bottom of the driver hub. It is intended to be made out of TPU or other flex filament. ...The corners have been enlarged for...

The REV Driver Hub's USB ports are not easily repairable. This model helps relieve some port strain by not allowing the cables to have wiggle room. I printed it vertically with the ports facing downwards. The mount is attached to the driver hub using...

Team 3954 Pink to the Future designed this protective Cover for the REV driver hub. Of course, all necessary connections/buttons are still accessible. There is a small gap (0,5mm) left free to adapt for printer inaccuracy. Because the cover is split...

This is a FTC REV Control Hub and Expansion Hub mount I remixed from TheEV. It holds the Control Hub and Expansion Hub on each side and has cutouts for the USB ports. There are holes properly spaced for GoBIlda holes. There are also holes to mount...

Housing for REV Robotics Driver Hub for FIRST FTC. Housing is designed to be printed from PLA or other rigid filament. Not as much cushion as TPU, but easy to print. Housing can be assembled as a stand-alone, or mounted to a driver station plate (a...

... exceed 5.5mm for those M3-0.5. Additional: The distance between the two mounting holes is 144mm. DISCLAIMER: In no way does this case guarantee any additional protection to your drivers hub, but one would assume it’s better than nothing. ...

D Collar hub

This is easy to release Driver Hub attachment that allows you to hold it from a pocket or belt and use magnets to prevent from sliding off of metal tables and surfaces. ... It uses : Two - M3 x 10mm Hex Cap Screws...

This is converted part models of REV UltraPlanetary and Core Hex Motors for FTC CAD models. ...Also any time you add the UltraPlanetary to any model it lags the whole thing.

This is a REV battery mount for FTC teams. It works vertically and horizontally. ...The peg is only needed when the mount is used horizontally and might need a rubber band.

This is a printed hub and the UltraPlanetary spacer for the FTC 11717 Circuit Breakers Ultra-Thin Drivetrain as featured on out youtube channel https://www.youtube.com/channel/UC6GGNby7DrRtbvfSQkb13dg. ... This goes between the sprocket and the wheel,...

FTC driver station. Includes mount for Samsung S5 phone, two Logitech controllers, a Plugable 2 port USB hub, a USB micro adapter cable, and stand for team pin. ...can be mounted on a microphone stand (not threaded).

FTC expansion hub

For FTC teams who would like to have an easier way to organize the controllers and phone on an easy-carry board like the FRC teams have (well, most of them). The two controller stands are made for Xbox 360 WIRED controllers. The small box in the...

This is a battery holder to use with the rev extrusion for FTC teams

A beautiful part to hold your USB HUB for FTC robotics. Add a little double sided tape on the bottom of the hub and insert it into the mount and yoru're good to go. This would be great if you want to build a driver station on a piece of wood. The...

This is a simple guard for [REV Robotics](http://revrobotics.com/) [15mm Extrusion](http://www.revrobotics.com/rev-41-1017/) and [10mm Small Pulley Bearings](http://www.revrobotics.com/rev-41-1368/). REV's pulley bearings are fantastic, but you...

Adapter for "non-FTC" mecanum wheels to be used with 6mm thick axels or Tetrix/Andymark DC motors use small m3 screws on the reverse side to mount on the hub use the spare mounting screws (slightly longer +5mm) mount on 6mm D-crosssection axle...

Rev Robotics Battery Holder

Protective case for the Rev Robotics Color Sensor.

power switch guard that fits the rev power switch mount

Moto G Rev 4 Phone mount with team name and number.

This is a Rev touch sensor mount that attaches to the Rev extrusion building system. It's a little weird of an position, and may not be exactly what you need. Have a good season! ... - Team 8417

This is a hex pillow block to use with the Rev 5mm shaft. Have a good season! ... - Team 8417

This is a pulley cover we have designed to attach to the REV Robotics channel. ...Attached are the files to print just one, or sixteen covers.