funko shelf 3d models
34521 3d models found related to funko shelf.prusaprinters
Funko Shelf with the box.Print in PLA 0.2mm layer height on the Prusa Mini+
thingiverse
My brother wanted a shelf bracket for his figures, so I modeled him one.
thingiverse
juste my take on a simple funko stand shelf for shelves size 12 and 18 Mm tell me what size your shelf is and i will make it apen here should print easy on any printer and any filamant
thingiverse
Quick Funko shelf build using Tinkercad. Based the measurements off of a shelf from Ikea. 115mm X 115mm Back set with 5mm holes for average drywall screw or can use command strips/double sided tape to adhere to wall. Placed Funko Logo on front...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
cults3d
INVISIBLE FUNKO POP SHELF - 3 Pieces Left, Center, and Right for a modular design. Will hold 1 Funko per shelf with a protector. Screw holes are 4.5mm, should fit drywall screws fine. I haven't officially tested the weight, but I did easily stack 4...
thingiverse
INVISIBLE FUNKO POP SHELF - 3 Pieces Left, Center, and Right for a modular design. Will hold 1 Funko per shelf with a protector. Screw holes are 4.5mm, should fit drywall screws fine. I haven't officially tested the weight, but I did easily stack 4...
thingiverse
This wall shelf supports one standard size Funko Pop figure. ...It only requires a single command strip and shows off your pop!
thingiverse
This is a shelf for a single Funko Pop (in box), to be used with 3m double sided tape to secure to wall. ...Recommend using supports over 80 degrees.
thingiverse
This shelf has been remixed to fit pops not in a case. At 25% fill, this bracket and the pop weigh very little, so it can be mounted right on to drywall. ... This is a remix of https://www.thingiverse.com/thing:3681777 which was designed for use with...
thingiverse
You can print 2 legs and 1 top, or if you want you can use 3 legs with 2 tops to make it larger I used the Standard Profile on Cura with an Ender 3 V2 - Funko Leg takes 38min - Funko Top takes 57min A set of 2 legs and one top with my configurations...
thingiverse
ive made the shelf big enough for the medium/ larger pops and all my medium anime figures have fit. there are a few cut outs to help weird bases fit as well. the lip on the front is the right size for an led strip (Govee) so you light everything up...
cults3d
ive made the shelf big enough for the medium/ larger pops and all my medium anime figures have fit. there are a few cut outs to help weird bases fit as well. the lip on the front is the right size for an led strip (Govee) so you light everything up...
grabcad
And Funko Pop is releasing those little toys representing each and every character of the show. So I bought them all, or I should say I will buy them all. Right now I've got 14 out of 24. I want to keep them in the box, so I asked my father if can...
cults3d
Remix of balonekcz's design to hold up a funko pop inside of an IKEA detolf, This is a WIP at the moment that requires an m3 bolt and nut.
thingiverse
Remix of balonekcz's design to hold up a funko pop inside of an IKEA detolf, This is a WIP at the moment that requires an m3 bolt and nut.
thingiverse
Remixed Steves pop shelf to use less filament and print faster. Added a few sized that were relevant for me. I attached all these to the wall with 3m command strips (3x 3lbs strips) and left the pull tabs intact behind the pop to allow for easy...
thingiverse
Hope you guys like it! I printed this using Cura, and selecting tree supports. make sure you deselect regular supports. no need in my opinion. I added v2. Stronger version. The old one was very prone to break at 25%infill. ...
prusaprinters
<p>Print support-free in the orientation as downloaded. I used wood filament and stained it, but any plastic will do. The pad is optional, but adds a nice flair of color. ...If you print the pad, I recommend super glue to adhere it. </p>
cults3d
This is a modular display system for your collectibles that will hold records, comics, video games, and DVD's. Leave enough room on the top mount to push the item up into the mount and pull over the bottom mount. allows you to display collectibles...
thingiverse
My first try at designing something to print using Autodesk Inventor. Have printed a handful of them and put them up using command strips. I designed these to fit my Pop!s that are in protectors. If you all have any ideas or things you are...
thingiverse
Funko pop shelf for funkos with or without cases. ... Printed in PLA+ .20 and 25% infill