g2c 17 round mag 3d models

Remix of OutwardB https://www.thingiverse.com/thing:4791004 The Ball Joint is by DieZopfe - https://www.thingiverse.com/thing:4739696 The Mounting system by HeyVye - https://www.thingiverse.com/thing:2194278 I wanted a mag base for use with a ball...

Removing and placing mags in is similar to the motions of reloading a mag into the p90/ps90 Use of stronger springs will make removing the mags harder but have better retention. You can rotate the back part for high or low positions. The completed...

The alternate mag release is a versatile upgrade suitable for all iterations of the FDL-2. It replaces the standard button with a lever-style mechanism, which may necessitate minimal smoothing to fit properly. The upgrade utilizes the identical pen...

Enhanced version of previous device Used for Mag pouch/carrier tools pouch or holster. Designed with enlarged area for more friction to get the most retention possible. 3D printed by PLA, light weight, low cost with short printing time. ...Easy...

The original was too small and the mag does not fit into it. I've increased the size one mil at a time till I got it to fit. It's snug, so don't be afraid to just push it in. ...Enjoy!!

Works with Ruger BX-25 and Butler Creek 25/22 mags but not the factory 10 shot(fits but tight) For a slat-wall with a distance of 75mm spacing with M5x15mm I am using the aluminum inserts in the wall so you may need different t-nuts if you are not...

The Melynda consists of six plastic parts: a base with two shelled plastic parts, a reader assembly with four plastic parts, and two molded parts encompassing the Mag Read track. The design allows for field replacement of the battery and access to...

Replaces button mag release in Motostryke. Take out button and lever, but keep the piece that interacts with the magazine. M1 is a simple paddle. M2 is a slightly longer paddle with an extended bit for the index finger of the rand hand to hit. ... I...

... swisgs freely when it's opened :) ( yes.. ...it's sitting inside with hot glue in the groove on top of this model and dropped into the dummy magwell hole... ) Todo: - Make it bit shorter - Lock-in mechanism - Functionality (too small for spare mag)

I wanted to attach my M4 airsoft mags to my Skadis wall. I took the airsoft model from https://www.printables.com/model/329881-m4-ar15-magazine-holder so all credit to them. I then added the hooks to the back. ... I made the hooks from this...

read instructions of usinngs bbs and silicone oil post print (in the picture) i will add a file where the mag is cut in half and has attachment pins to join and glue after print for anyone whose print bed is too small. mag must be joined correctly...

I added a hole near the top to allow passthrough of a USB cable which plugs into the Quad Lock Mag Head wireless charger. I also added a little open storage area on the bottom of the stand for things like the Quad Lock Phone Ring, which you have to...

Glock Mag Adapter designed specifically and tailored for your high demands today providing best results from reliability performance efficiency coupled together across multiple use areas in real-time keeping officers trained proficient professionals...

5 mag holder for airsoft mags that fit the Ikea Skadis board, model will use 5 points on the skadis board, comfortable fits 5 magazines.Print with manual supports on the bottom hook mounts(see images), a brim might be needed to insure good print...

There are three sizes available: one that fits a standard Mini-Mag flashlight (2AA), another designed specifically for an El Cheapo aluminum 3AAA LED light from Harbor Freight and other brands, and a third size that perfectly fits a 1AA pocket LED...

Caso queira me ajudar com uma doação este é o meu PicPay ==> @luke.driano This magazine has a capacity more than the normal aep mags, let's say it is a "mid cap" or "Hi cap". To use this magazine you will need to buy the spring for pistol magazines...

... got the mag working perfectly. A warning: you will quickly go through pellets. I created five mags, and before I knew it, I had emptied 500 tins using four Co2 cartridges. ...Pellets used: Crossman Prem hollow point 14.3g with a velocity of 587fps.

There are three versions of each size, with a different tolerance of the mag fit. I Recomend that you print one of the singles first to see which tolerance fits your mags best. The magazines are held in place with friction alone so if you print one...

there are 3 versions: 1) Tape - larger back with an inset to apply with double-sided tape (Similar to what came on my bike) can be printed in any material but I would recommend TPU or PETG 2)Slide in Mag - No supports needed, but NEEDS TO BE PRINTED...

I also redesigned the mount because I wanted more support for the mag on the rail. My reloading habits made me tend to push the original mount back on the rail, so I added more contact to prevent it from falling off. ... To keep the mag secure, I added...

... packaged in a PDF document that's ready to download. Note the blue pieces on the pictures and be sure to check out the red piece available for sale at http://www.kg-factory.fr/en/paintball/36-adapter-charger-tipx-tpx-universal-mags-adapter.html

A Waistband Pouch for Two Standard Capacity USP 45 Mags is Designed. Ideal for Range Time, Hiking, or Backup When Hunting. Three Versions are Available. The Printed One in the Pictures has a Hollow Tear Drop Core to Save Material and Reduce Print...

The original mag was proving to be too difficult to pull out of the gun while wearing gloves, so I created this accessory to make it significantly easier. ...Print out both parts and join them together using superglue - I've found that it works best in...

... I translated the provided information to produce a comprehensive 3D model of the Wing within Catia. The ribs are made from foam, while plywood serves as the covering material. For further insight, visit http://mag.01.pagesperso-orange.fr/index.htm.

It's a Mag-Lifter, essentially a forklift powered by magnets. That gives it a futuristic twist. It assembles easily without adhesive of any kind. The grabbers pivot to the left and right, and also go up and down. This model is designed specifically...

... drone configuration. ...The top is designed for a 3DR Mag/GPS unit but accommodates most GPS units. To assemble, glue the pole top piece and GPS holder using hot melt adhesive. ...You will require an 8mm outer diameter fiberglass or carbon fiber tube.

My inaugural try at a mag wheel for my 1:10 scale nitro touring car is now complete. The wheel was printed at 100% with supports in ABS, and it feels remarkably solid despite not having been tested yet. I'm confident that it will hold its own against...

This is a magnetic holder for the iPhone 12 series with mag safe... it takes the small 8 mm magnets I saw at Harbor freight. I did 2 thick and when you place them the outer ring put the magnets the way they stick to the outside portion of the ring...

I lost the back to one of my worker hurricane mags during painting. This is a new back spinner. It is designed to look and feel like the old one. Print Settings Rafts: Doesn't Matter Supports: No Resolution: .05 Infill: Doesn't Matter Filament:...

A set of paddle mag releases for the TalonClaw and TalonClaw U! The standard version is two parts, one half for Talons, one half for Katanas. I have also included two other versions that use ONLY Talons or ONLY Katanas. Enjoy! If you wish to...