g2c holster 3d models

Here is my rendition of a simple holster for my Taurus Pt111 G2. I used PETG for now which works, but ABS or ASA might be better suited for a really long lifespan. I used 0.2 mm layer height which averaged a 4hr print. ... And if you feel like it, you...

Taurus G2C pistol Full scale model (Modeling from reference images and measurements, some measurements and details may deviate from the real model) Single block for 3D printing Trigger reinforcement to prevent damage to the structure

Bumper for Taurus G2C pistol. Two different models, both with Taurus logo on their sides. Full scale model. ... NOTE: The 3D view of BUMPER in cults is having performance issues and presents the model as if it were deformed.

https://cults3d.com/en/3d-model/tool/taurus-pt111-g2-g2c-holster# I also made a version with a "claw" and slightly angled positioning to pull the grip in against the body to help with printing. Works well for me when carrying appendix. I have...

https://cults3d.com/en/3d-model/tool/taurus-pt111-g2-g2c-holster# I also made a version with a "claw" and slightly angled positioning to pull the grip in against the body to help with printing. Works well for me when carrying appendix. I have...

Bumper for Taurus G2C to increase the grip

Taurus G2C Pinky Extension for my fat fingers.

This fits G2C 9mm magazine It is a bumper, and you need to install like the OEM

This is a dimensionally accurate model based off a real G2C magazine. ...used for practicing magazine changes where you dont want to damage the magazines.

2 different versions of the Taurus g2c frame I redesigned to look a bit more oem than the frame out there I've found. One version has a nice beaver tail that looks excellent. ...Enjoy

These are pinky extensions for Taurus G2C magazines, 9mm and 40 S&W. I've had best results with PETG. The 9mm base has imperfections. I have not successfully printed two at once. Something always causes failure at the same point near the end. I...

Remix of schicksters Taurus G2C speed loader. I quite liked the original concept, but, after printing and testing the loader, I found that the sharp edges quickly rendered it unusable past a couple of mags. In this version, I softened the edges...

Low texture holster for my college project. ...Just a test.

used Goodwynn89's basic design, then did many renditions and tweaks to make it fit. ...Finally a free .STL for the G2C 18 rnd mags!!!!! ... Hope everyone enjoys!

Speedloader for Taurus G2C and G3 mags. Slightly loose fitting. ...The plunger is concave on the end and the angle matches the 9mm rounds as they sit in the mag.

Magazine for the Taurus Millinium G2C. Regular mag, and extended with the magazine sleeve. ... I got these stl files from somewhere i forgot but originally the magazine bottom was slightly cooked, so i fixed that and also made a regular 10 round...

Municiador rápido para magazine Taurus G2c.

Luva para G2C 9mm montado no carregador da G3 17 munições. Também compatível com o Carregador TS9 17 munições, (deverá fazer o encaixe do retém neste caso). ...È um pacote com 3 arquivos, um liso, um com o logo da taurus e outro com uma caveira.

A friend mentioned the other 9mm easy loaders did not work for their Taurus G2C, So I got some measurements and they are helping me iterate the design until its just right. 20220428 - This is gen 2 - not good 20220428 - Gen 3 ready for trial ...

The original Taurus G2C Mag Base had a sharp edge on the top rear. Technically it still fit into the gun when attached to a magazine, but it would dig into the polymer grip. This remix added a rounded edge that matches the grip pretty much...

magazine Sleeve for P226 magazine used with GxC pistols G3C sleeve for SIG P226 Taurus G3C, G2C, PT111 G2.

Bumper projetado para melhor empunhadura para atiradores esportivos. ...(Encaixe Perfeito) Tamanho 26.6 x 52 x 26,4mm

I made some small mods to the original loader by red112. I wanted some 'knurles' and felt that the 'pusher' should be a little further back. This is what I came up with. ... Original can be found here: https://www.thingiverse.com/thing:2055868

Bumper, desenvolvido no SolidWorks

Bumper, desenvolvido no SolidWorks

Customized version of https://www.thingiverse.com/thing:148722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148722

A design for Fusion Blades. Designed to be used on Games Workshop® XV25, XV8, XV85/86, XV88 models. Also will work on Tri'dent Forge Models (Coming soon). They come in either Magnet( M3x1 ), or post install. This was designed for a Resin...

A design for Fusion Blades. Designed to be used on Games Workshop® XV25, XV8, XV85/86, XV88 models. Also will work on Tri'dent Forge Models (Coming soon). They come in either Magnet( M3x1 ), or post install. This was designed for a Resin Printer.

Customized version of https://www.thingiverse.com/thing:148722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148722

Customized version of https://www.thingiverse.com/thing:148722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148722