g303 mods 3d models
33090 3d models found related to g303 mods.thingiverse
If you want this mod but don't have the confidence/willingness to undertake it yourself, you can get in contact with me on reddit (u/Nuvolari48) or discord (Burt#3494) and maybe we can work something out. Anyways, Story time for those that like it:...
myminifactory
If you want this mod but don't have the confidence/willingness to undertake it yourself, you can get in contact with me on reddit (u/Nuvolari48) or discord (Burt#3494) and maybe we can work something out. Anyways, Story time for those that like it:...
thingiverse
Its functionally the same as my V2 mod but the side buttons mount to the top shell now and its 69mm wide which is as narrow as I can get it. You will have to trim down the left and right click PCB (clip those little tabs off the sides. you'll know...
thingiverse
I scanned and modeled the sides from a g303 and have attempted to fuse them to a g305 shell. I designed this to swap out the factory g305 lower shell and thumb buttons. No parts get destroyed and the donor g305 can be reassembled back to stock. ...
myminifactory
Its functionally the same as my V2 mod but the side buttons mount to the top shell now and its 69mm wide which is as narrow as I can get it. You will have to trim down the left and right click PCB (clip those little tabs off the sides. you'll know...
thingiverse
Plastic Enclosure of company Gainta model G202/G303 (Polycarbonate/ABS)
grabcad
Plastic Enclosure of company Gaintamodel G202/G303 (Polycarbonate/ABS)Neoprene gasket with a diameter of 2...2,5 mm. ...In the model it is shown as a compressed
thingiverse
Its functionally the same as my V2 mod but the side buttons mount to the top shell now and its 69mm wide which is as narrow as I can get it. You will have to trim down the left and right click PCB (clip those little tabs off the sides. you'll know...
thingiverse
The raw scan I took of the G303 top shell, it has over a million triangles so I also included a decimated version that I cleaned up just a bit as well. ... Use this as a reference for modelling, I wouldn't say these are printable.
thingiverse
Instead of using heat-shrinks for my gaming mouse paracords, I am aiming to make a set of 3d printable stress reliefs for the major manufacturers. The heat-shrinks generally look bad, do not work for all mouse manufacturers (Endgame and Logitech have...
thingiverse
Uploading now as my printer will be out of commission for a bit - fortunately I've dialed these in to a point I'm happy with atm but I would like to tinker with them more to just to experiment later on.
thingiverse
Quick edit: When the top shell finally clicks into place when the side panels and buttons etc are all in and screwed in, the pretravel on the side buttons will be like a stock G303. The pretravel on the side buttons without the top shell is not what...
thingiverse
Antenna Mods Andy Valentine Jetsam mod https://www.patreon.com/itsandyvalentine/posts
cults3d
Antenna Mods Andy Valentine Jetsam mod https://www.patreon.com/itsandyvalentine/posts
thingiverse
Various mods to add armor or make the androids a bit more gundam-esque. ...Very blocky, very low quality, but perhaps a good start for something better.
thingiverse
hammer shot mods tp improve the fun times Includes: 7 round Cylinder Hammer and parts to move the cylinder all but the hammer are needed
cults3d
Various mods to add armor or make the androids a bit more gundam-esque. ...Very blocky, very low quality, but perhaps a good start for something better.
thingiverse
A couple of mods I made to the FB 2020. I integrated the corner bracket with the y-axis rod clamp. ... I also thickened the top piece of the carriage where the idler mounts for more strength.
thingiverse
Updated content : 05/03/2019: Runcam3s mod of the tiltable HDCam mount. 24/02/2019: A V2 of the Falkor mounts. A bit back (but you still don't see the frame), and thinner to fit better in the frame. A V3 of the pigtail/ImmortalT. Longer arm and...
prusaprinters
These things are created on the theme of mod menus Print Settings Printer Brand: Prusa Printer: Mk2.5sRafts: No Supports: NoInfill: 25 Filament: Doesn't Matter Doesn't Matter Your choice Post-Printing Category: Accessories
thingiverse
Modified parts for Zaribo mod. All were remade from scratch but credit goes to Prusa Research, Wolfgang Shadow, Murathan Araz and Stwebster. Parts are made for Misumi 3030 section with 4 holes through for cable routing. X is made to use with...
cults3d
I also encluded a 40mm fan mount off to the side for part cooling.(This is a work in progress, expect changes) Last is an untested tensioner I modeled up for the x-end, This mod will require 2 8mm bolts and 2 8mm nuts. The hexagon portion attaches...
thingiverse
I also encluded a 40mm fan mount off to the side for part cooling.(This is a work in progress, expect changes) Last is an untested tensioner I modeled up for the x-end, This mod will require 2 8mm bolts and 2 8mm nuts. The hexagon portion attaches...
thingiverse
You can see a video of it in operation here - https://imgur.com/a/iCBeDjZ Edit - my original 2 x gluestick mod works well on my 1250KV motor but was asked to produce a 4 x gluesitck version for a beefier motor which you can find above (although I...
thingiverse
All of my mods are printed in Taulman 910 Nylon. I used M3 inserts in the diff lid to screw the bumper into. I Know KrisCubed wanted this thing to work with PLA, but I haven't printed PLA in years, and ABS just wasn't going to cut it, so out came...