galaxy orb 3d models

I just finished printing, finding a stone and doing the painting on tonyyoungblood on thingiverse's Orb from Guardians of the galaxy, with a remix i did using 2 Neodynium magnets cut into the outer rim, which do not effent the final look of the...

So I printed tonyyoungblood's Guardians of the Galaxt orb, then realized I needed some place to put it. ... This is a quick little stand, simple, no supports needed

Ok this will be a good addition to the Guardians of the Galaxy Infinity Orb. Drilled small hold in one of the areas that the SW would fit in and fed the wires through the hole to inside the Orb. Drill another small hold in the bottom center in one of...

This is a stand for tonyyoungblood's Infinity Orb from Guardians of the Galaxy. ... Link: https://www.thingiverse.com/thing:430184

FRANÇAIS LIENS EN BAS Bonjour, Je vous présente l'orb des gardiens de la galaxie sur un support en lévitation ! L'orb est imprimé en résine, peint en noir puis en or pour le centre et recouvert d'une sire silver pour l'extérieur. J'ai percé les...

Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. In one of the pictures, you can see a side by side comparison of my orb and the orb from the film. I tried to replicate all the hole shapes to the best of my...

I have uploaded two rings with recessed places for the magnets one from the front One from the back of the ring From Harbor Freight (item 67488) about $3 for 10 Rare earth Magnets 5/16” diameter x 5/64” Thick http://www.thingiverse.com/thing:430184...

I have taken the origional rim and cut out 3 10x5x3mm pockets. Then you can insert 3 neodynium magnets ( 10x5x2mm cheaply bought on Prime ), just remember to align the poles correctly be before gluing into place. The first one i printed with 2...

Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. It's a work-in-progress. So far I've completed the outer shell (second draft), the rim (first draft), and both halves of the interior (final draft). . In one of...

Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. It's a work-in-progress. So far I've completed the outer shell (second draft), the rim (first draft), and both halves of the interior (final draft). . In one of...

This version of the rim has recesses for installing magnets, which will hold the two halves of the orb together. Print two copies of this part; they are designed to fit together. Use eight, 10x5x2mm neodymium magnets. This idea is borrowed...

THIS HAS BEEN REDESIGNED TO BE MORE SCREEN ACCURATE: http://www.thingiverse.com/thing:547100 I'm leaving this design up in case anyone still wants to use it, but recent images from the Guardians of the Galaxy DVD have indicated that the base the orb...

I initially thought the 'base' that the orb magnetizes down onto was a solid triangle, but it instead appears to be three prongs pointing inwards. Instructions Print three (3) of the corner piece...

Guardians of the Galaxy Orb Holder

Coronation orb

Sphere inside of an Orb

Sphere suspended inside of an Orb

https://www.thingiverse.com/thing:4441076 Make amazing glowing orb of any colour or size.

This is a stand for the Guardians of the Galaxy Infinity Orb. It is a quick and easy print. I really enjoyed this model but was disappointed that it always had to be closed. ...I designed a stand that shows off the detail of the inside and gives the...

Infinity orb from guardians of the galaxy

orb

Snorlax orb

Mamoswine orb

The Orb

Shelgon orb

Umbreon orb

Gengar orb

Pikachu orb

Houndour orb

retopology an orb