garden hose connector 3d models
99714 3d models found related to garden hose connector.thingiverse
This is a simple copy of the pattern for a Gardiner-style push-fit garden hose connector. The Solvespace file is provided should you need to modify it. ...It is a tight fit - I might try and reduce it a bit (I will update if I do).
prusaprinters
Simple solution to a problem that I found very annoying (see before/after pics). (!!!) Slicer settings: Top layers count: 0 Bottom layers count: 0 Print Settings Printer: Tronxy x1 Rafts: No Supports: No Resolution: 0.28 Infill: 50% grid Filament:...
thingiverse
This is an OpenSCAD model of a garden hose quick connector. After I created this model as I need to combine it with other part models. In the bottom is an indent if you want to glue other parts on to it, remove it and the membrane if you don't need...
thingiverse
Simple solution to a problem that I found very annoying (see before/after pics). ... (!!!) Slicer settings: Top layers count: 0 Bottom layers count: 0
thingiverse
Connect a garden hose to my FibroPool submersible pump. ...Fusion file is included in case you wish to adjust yourself. Thanks to the linked re-mix for the threads.xml file for a garden hose.
prusaprinters
For body use brim, supports not required.if you need connector to 3/4" hose then set scale factor to 130% in X and Y coordinates for 1" hose connector set scale factor 200% in X and Y coordinates and 120% in Z coordinate Happy...
thingiverse
I use this part (in PETG) in my garden drip irrigation system to connect drip tubes and it works just fine. This 16mm straight tube coupling is enforced with 2 extra rings in the middle so it doesn't break as easely. Also there is no need to glue...
thingiverse
Faucet_Connector_Gardena_Gasket02 from thing 5289793 worked fine for me as the O-ring. I added the model here on this thing page for ease of finding it, but i do not take any credit for the design. I recommend printing the adapter from ABS or ASA...
thingiverse
This is a male garden hose connector on one end, four 1/4" connectors on the other end. They fit 1/4" irrigation tubing snugly. This is improved over my first version, since it has "ears" that will allow you to twist the connector into its...
prusaprinters
just part of the hose lock. this is prepared to be used in your project. Is compatible with 1/2" (13mm) fastlocks (Gardena, Fieldman, Hozelock, etc.). ... </p><p>For right production you need to use O-ring 11x2.5 mm or print is from...
cults3d
3/4" male quick connector 3/4" Female quick fit connector Hose connection 3/4" - 3/4". ...All parts are designed for a European house, therefore built with 3/4 "(= 3/4" and 14 TPI BSP threads (the outside diameter of the male part is 26.441 mm or 1.04...
youmagine
- 3/4" male quick fit connector- 3/4" female quick fit connector- 3/4" - 3/4" pipe joinerAll parts are designed for an european household hence built with 3/4" BSP threads (=3/4" and 14 TPI (male part OD is 26.441 mm or 1.04")).
thingiverse
PLA - 200 - 60 heated bed - raft - no supports This is a terrible garden Y. ...The lawn looks like a dust bowl and I'm using this to attach 2 sprinklers to a garden hose. This is over engineered not to leak. It still might. ...
thingiverse
Garden hose 90 degree connector 21mm Inner diameter, 25mm outer diameter 2 versions: more beautiful & faster to print
thingiverse
This is my connector for 1/2" garden hoses. Just print two of the halfs and glue them together with super glue. Look out for the alignment of the halfs to minimize water resistance. You also have to print two of the screwcaps. I recommend PETG or...
thingiverse
... with a little force. Some hose connectors will reach the end when you twist them on and then have a "give" and disconnect, twist the hose on until you feel its tight and if it snaps out, just tighten it again but not so tight it comes loose again.
thingiverse
For multiple waterballoon fillin with garden hose. O-Ring needed for proper sealing. ... Not printed, not tested.
thingiverse
This is a short version of my 1-into-4 garden hose connector. This makes it a bit stronger, and it's still plenty long for 1/4" irrigation tubing. Print Settings Printer: Monoprice (Flashforge Clone) ...
thingiverse
This fits (at least) for me for common garden hose connector. This thing is intended for Parkside aku compressor PKA 20 LI B2 (https://www.lidl.cz/p/parkside-aku-kompresor-a-pumpa-20-v-pka-20-li-b2-bez-akumulatoru-a-nabijecky/p100350378) to clean...
thingiverse
A set of connectors and plugs for low pressure ( rain water ) irrigation using standard 13 mm garden hoses.
thingiverse
Male hose connector for Melnor quick connect 237-337.
prusaprinters
... glued-joint failing. ...This lets you thread on a garden hose instead. The use of male threaded part plus a separate female coupler is used so it prints without supports. It requires a garden hose washer/gasket so that it does not leak.
myminifactory
... sand-cast outdoors faucet. ...Its dimensions are dubious, and the design is somewhat less than symmetric. To attach a standard garden hose fitting, I needed something that could be tightened enough to deform to fit the faucet. ...Hence this version.
thingiverse
BSP thread standard EU size, 1" and 3/4" If you need a different size, contact me, I might be able to help. Sealing ring is standard ruber ring. 1" OD=30mm ID=20mm 3/4" OD=24mm ID=16mm You can try to print it from TPU, I haven't tried but...
thingiverse
This is related to my 1x4 adapter here: https://www.thingiverse.com/thing:1498649 Someone asked for one with 2 instead of 4. Here you go! Let me know if you have any issues with it. ... It should print just fine without supports.
thingiverse
Like 4 hoses, impact sprinklers, oscillating sprinklers and misters, switching them around, just having fun. The screens falling out of sprinklers or misters with fine holes meant grass clogs. So I designed this to thread the male end in to hold...
thingiverse
Garden hoses to quick release connector. ... upd1: add no support needed version, add skirt only And yeah, If You like my work and ideas, feel free to support me with a couple of bucks.
thingiverse
This is a quick hose connector remixed from gm276's desing. The 15mm side may be a bit too snug. ...Sanding helps.
prusaprinters
NOTE: garden hose connections require a rubber washer to seal, unlike plumbing threads, the thread is not designed to make a seal.The GHT “standard” is weird, here's where I got help getting it into...