garden hose splitter valve 3d models
61588 3d models found related to garden hose splitter valve.thingiverse
This goes over the thumb knobs of a faucet splitter you can commonly find at Lowes, Home Depot, etc. so that you can have a larger handle making it easier to turn the water on and off. The left and right are mirrored each other. I think it fits...
thingiverse
This garden hose barb splitter works with 3/4" garden hoses (OD), approx 5/8" ID. Pressing the hose over the barbs locks the hose in pretty well, didn't need any hose clamps but its tough to get the hose out if you will be connecting and...
cults3d
I made this little object because the splitter I use on my garden hose system gets to be very difficult to turn. I also need to make very fine flow adjustments to facilitate a water timer used in a system to water many items. I made it on a whim,...
thingiverse
I made this little object because the splitter I use on my garden hose system gets to be very difficult to turn. I also need to make very fine flow adjustments to facilitate a water timer used in a system to water many items. I made it on a whim,...
thingiverse
The cheep Y type of garden hose valves tend to corrode over time and become very stiff. The wrench gives you the extra leverage you may need to operate an old valve. Instructions Build this part...
prusaprinters
If you want to feed 2 drip hoses from one tube you normaly need a Splitter and 4 hose connectors and a bit of extra tube. This type of connector just need 2 connectors to connect 2 drip hoses to one water hose. Additional parts you need2...
thingiverse
I made this from scratch as a replacement lever for my garden hose splitter after it broke off. The measurements are pretty precise. I printed in 0.1 mm layer height for the detail, with supports just for the screw hole. If you have this part, you...
thingiverse
This was created to solve the problem of the lever arm being too small and never knowing which way to turn the valve off. The OFF nomenclature is on both sides. Arrow is cut through. If your valve closes the other way for some odd reason, flip the...
thingiverse
I printed the Garden Hose Valve Helper to give leverage to operate the valve on a Y adapter, but due to the orientation of the handle, it knocked against the hose spigot. Also, the valve on each side of the Y operates in the opposite direction, so...
thingiverse
The handle on my garden hose valve broke. So, I measured it, designed a handle on Fusion 360, and printed it out on my Wanhao I3 Plus printer. It came out pretty good. I printed in PLA at .15 layer height and it needs no supports. It's a tight...
thingiverse
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). ...It seems to do the...
youmagine
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). It seems to do the...
thingiverse
hose splitter, non standard sizes. ...manually measured hose i have at hand..
cgtrader
Garden hose ball valve 3d model. ...Polycount: nosub - polys 13086 verts 13221 1 sub - polys 104688 verts 52609
thingiverse
If anyone wants to tinker with the Fusion 360 file here is the public link: https://a360.co/2JdQGrr Designed to be used with 1/2" inner diameter no PSI soaker hose off of a rain barrel. I wanted a way to shut off certain area's without shutting the...
thingiverse
This is a replacement ON/OFF 3/4” ball valve operator for the Vita Guardian 75 foot expandable garden hose. The original operator included with the hose fell off and was lost within days of purchasing the hose :( This replacement is a perfect fit. ...
thingiverse
It seemed odd that no one at all makes mounts for the garden hose valves you find at your local home improvement or hardware store. The inexpensive valves (*like the one I used*) work well enough but there is no way to mount them. Some variants have...
cults3d
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). ...It seems to do the...
thingiverse
My mother has pretty advanced arthritis, but also loves to garden. Unfortunately our water tap has a tiny hard to open lever on it(pictured ). I'm a total amateur, but I designed a simple handle to make it easier, and it's worked amazingly well. ... ...
grabcad
My proposal for : https://grabcad.com/challenges/oxygen-valve-splitter