gardena quick connector 3d models
127622 3d models found related to gardena quick connector.prusaprinters
<p>The fine thread M22x1 is often used for in house water taps.</p><p> </p><p>You need in addition a O-ring and a rubber gasket for the connection between adapter and the water tap.</p><p> </p><p>Printed with 0.12 layer height and in...
cults3d
printable gaskets) for connecting - Hose to hose, - Hose to faucet, - Hose to Gardena (R) compatible, - Gardena to Gardena Hose to hose: - Faucet (3/4") to 1/2" hose - print one gasket of type 1 - Short straight (directly connect 2 hoses to each...
thingiverse
printable gaskets) for connecting - Hose to hose, - Hose to faucet, - Hose to Gardena (R) compatible, - Gardena to Gardena Hose to hose: - Faucet (3/4") to 1/2" hose - print one gasket of type 1 - Short straight (directly connect 2 hoses to each...
thingiverse
Adapter from G 3/4-14 BSP thread to Gardena hose quick connector broke. Here is my replacement. ... Printed with esun ABS, golden color 0.15mm layer height, 0.62mm extrusion width But different parameters should do, as well.
thingiverse
This adapter uses a slightly updated version of my male Gardena quick connector for better o-ring fit, combined with my 1/2" NPT thread (excellent spec. thread) to create the entire adapter. I required this adapter to test a "new" water nozzle and...
thingiverse
This adapter also uses a slightly updated version of my male Gardena quick connector for better o-ring fit, combined with my 1/2" NPT thread (excellent spec. thread) to create the entire adapter. Enjoy! ... This adapter could also be used to "test"...
thingiverse
Quick connect to Gardena hose coupler. I use it for cleaning my equipment when I'm homebrewing. ...I printed with a brim and no supports in Cura with the QD end facing down, then trimmed the brim after the print.
thingiverse
This connector can be used to interface between female Gardena-style hydraulic connectors and male UTP cables. The part is as of yet untested. ...WARNING: do not use in combination with PoE.
thingiverse
Easy to print Gardena compatible multi-connector with good water sealing. The connectors are fitting tightly but are easy to connect/disconnect. I only printed the 6 connectors version for a project. The 4 connectors version is provided AS-IS and...
thingiverse
This print allows you to mount a convenient gardenhose connection point on any surface. ... It accept a standard gardena hose connector on one side and a 3/8 BSP Thread on the other. ...
thingiverse
Remake ====== This is a remake of "Gardena 24mm Hose connector" by Etlaare, **BUT** tweaked because his version leaked at the Gardena endpoint and I needed a smaller diameter on the non-Gardena side. Misc ==== - I first just adjusted the...
thingiverse
Gardena style quick connector with 3/4“ NPT thread. Update: Version 2 has a smaller inner diameter and should be more durable. ...It also provides a notch for better support of the rubber seal.
cults3d
i wanted to connect my gardena fruit picker on my broom handle. ...:)
thingiverse
A solution to connect a standard Gardena hose fitting to a HDMI cable.
prusaprinters
Easy to print Gardena compatible multi-connector with good water sealing. The connectors are fitting tightly but are easy to connect/disconnect. I only printed the 6 connectors version for a project. The 4 connectors version is provided AS-IS and was...
thingiverse
i wanted to connect my gardena fruit picker on my broom handle. ...:) Instructions 50% infill 0.20mm layer
thingiverse
I got a cheap micro drip system and had no fitting to connect it to my gardena pipe so I made one.. Works great ! Don't know if it's ½ or ¾ but outside diameter of the thread is 25 mm. Could certainly be improved but it works fine for me.
thingiverse
I had this old adapter to connect a Gardena plug to a large 25mm or 1" hose. Sadly it broke but then I realized I could rebuild it and make it better .. stronger .. faster and above all smaller ;-) Print Settings Printer Brand: ...
thingiverse
This is a gardena quick connect compatible male end for all of our sprinkler/garden accessories.
thingiverse
I had some old Gardena Quick Hose Connectors laying around. I connected them to the printed parts (which is a gardena nut with a foundation), and have a quick connection to the storage of my gardena tools. ...As a bonus I can use the underside of the...
prusaprinters
Connector for 15mm Gardena MDS Pipes.2 O-Rings are needed. ...(9 mm x 1.7mm) </p>
thingiverse
This connector goes from 29mm I.D. x 90 deg Gardena end. Needed this custom fitting to prevent kink in a hose due to short radius. ... Fusion 360 File included so it can be easily modified.
thingiverse
Gardena connector for mounting on a wall. == Print with connector upright! (Not as displayed here.) For printing in Cura, you need to select "union overlapping volumes" under "mesh fixes". The model includes support on the nut, but needs support...
thingiverse
#Gardena connector for surface mount This connector is intended to abuse a garden hose for air, e.g on things like www.thingiverse.com/thing:3459167/comments The nut at the top is not missing, but it's hidden below an integrated support. There are...
thingiverse
It connects the water inlet hose through the rotating reel to the connector inside the hose reel that feeds the main hose. After a long search, no like part or replacement part was available and this was the only broken part preventing the use of...
thingiverse
Allows you to connect the Gardena microdrip 13mm system to an electric water valve. Thanks, Enjoy! ...