garmin livescope cable saver 3d models
101092 3d models found related to garmin livescope cable saver.thingiverse
Top mounted mount and cable saver for Garmin Livescope that will do forward and down view without the use of a knob to untighten. ... Simple put together pieces with a bold and a flexible rubber washer or spring so it's tight enough to hold angle but...
thingiverse
This part is for the Garmin Livescope transducer. This part should help prevent the transducer cable from cracking/breaking when it meets the transducer. ... Additional Items needed to attach part to transducer: -4 Stainless M4-.70x12 screws
thingiverse
These cable clips are sized accordingly to fit the pole that I use for my Livescope Ice Fishing Bundle (Summit Fishing Equipment). Small, medium, and large clips to fit each section of the pole. The clips also feature a tab that locks the clip into...
thingiverse
Protective cover for expensive Livescope transducer. ...
thingiverse
This is a tripod design for a extendable paint pole, to use for Garmin Livescope transducer ice fishing. Should fit any pole with a 1.25" OD. Connected with 1/4-20 1.25" round head screw & nylon locking nut. ... Pole I used: ...
thingiverse
I adjusted the Livescope_Mount_v4.stl to include a cap (Livescope_Mount_Cap_v1.stl). I had an issue with the bolt that mounts the actual transducer on would loosen over time. I was worried it would be at the bottom of the lake eventually so...
thingiverse
... remix this and tweak as needed. I suggest you print in TPU so it can have a slight bend. The bolt that secures the transduced goes through the cable saver, which locks in with the teeth on the PS22. ... Please post any makes as well as remixes.
thingiverse
Mount for the new Garmin livescope transducer for use with perspective mode. Best when printed with PETG or ABS. Nylon is nice but just a bit too flexible for my tastes. ... Enjoy.....
thingiverse
This is an arrow used on my homemade transducer pole for the Garmin livescope. It fits standard 3/4 PVC fittings. It is shown glued to a 3/4 PVC tee. Nothing fancy. ...Just makes life easier.
thingiverse
Garmin Panoptix Live LS 32 cable saver. ... You need 4 kpl RST M4 x 10 mm to connect transducer.
cults3d
This is a protector for the Garmin Panoptix LVS32 transducer cable output, as it is a weak point that has and so we will avoid that it breaks there and then have no fix. Easy to place and that with two M4 screws will be subject, quite resistant with...
thingiverse
This is a clip used to secure the Garmin Livescope transducer cable to attach to my homemade mount. Was using electrical tape but did not like it when I spun the transducer head around too far. Was concerned about binding the cable too much. Made...
thingiverse
I created this so I could use my Livescope System Ice Fishing without having to spend $150 on one from a store. The pole is one half of a kayak paddle. The paddle is 30mm in diameter. The adapter was designed to slide over the smaller end of the...
cults3d
A movable mount for your garmin lvs32 transducer . no problem to turn 360 degrees and even tilt the transducer if you prefer that. the mount have holes for a 25mm rod but i have included the cadfiles that are made in 123d design if you want to tweak...
thingiverse
No modification only save it as .3mf to help people print it :) all the credit to blizzard317
thingiverse
Here is a real world tested Garmin Livescope Sonar transducer mount. It allows for Forward view, down view, and perspective mode, all in one mount. Designed to attach to a pole mount, this particular file accommodates a 28mm pole. (I built my pole...
thingiverse
Cable savers for Lightning cables. ... USB-A end and Lightning end, USB-C end and Lightning end.
thingiverse
Saves your micro USB cable from braking (non universal) Cable head measurments for a good fit: 7.7 X 10.6 X 10.18mm
thingiverse
... the part dense it is printed with 6 shells. Print temp was 245, bed @ 110 degrees C. This is such a simple part allowing for many other print options. Too bad Garmin doesn't include this wedge for zero degree pole mounting with the Livescope kit.
thingiverse
Extended the original lightning cable saver as my daughter's cable was destroyed exactly where the original saver ends.
thingiverse
I just made this cable saver for saving my good old UGREEN USB-C cable from dying.
thingiverse
A cable saver / cable boot for the Macbook Retina Laptops (2012 onwards) Print with or without a brim or raft depending on your bed adhesion.
prusaprinters
Lighting cable saver for standard Apple lighting cable. The cable saver clips together to completely protect the cable. Print instructionsI printed this in PETG, I think the clips might crack in PLA. Printed with a 0.4mm nozzle, with 0.2mm layer...
prusaprinters
A cable saver / cable boot for the Macbook Retina Laptops (2012 onwards) Print with or without a brim or raft depending on your bed adhesion. Print instructionsPrint upright
thingiverse
... fit the part around the stepper motor being sure to run the end stop wire under the bridge. Step 3: Use a cable tie to secure the cable saver in place Step 4: use a 2nd cable tie to secure the cable with sheathing to the cable saver
thingiverse
My quick 'n dirty design for lightning cable end saver. ...I made the cut very tiny because it is meant to be printed with TPU for it to be flexible.