garmin striker 4 models
2193523 3d models found related to garmin striker 4 models.thingiverse
GARMIN STRIKER PLUS 4 Tilt/swivel mount (Garmin Dual Beam Transom Mount, Traditional 500 W (77/200 kHz) Transducer )
thingiverse
This is a Garmin Striker 4 transducer mount that clips into a gopro clip under a kayak. The clip itself has been modded a little to make it stronger. ...i suggest painting it in epoxy or something to help it last longer.
cults3d
The Garmin Striker 4 is the smallest GPS/Depth finder I could find. (I know there are phone options, but I preferred the purpose built device (especially for the price). I didn't want to drill into the boat any more than necessary. My boat (1960...
thingiverse
The Garmin Striker 4 is the smallest GPS/Depth finder I could find. (I know there are phone options, but I preferred the purpose built device (especially for the price). I didn't want to drill into the boat any more than necessary. My boat (1960...
thingiverse
This is a case for the Garmin Striker Plus 4. It is a slide-on case that pressure fits so it doesn't fly off. I created this so it can stay on while driving down the road and yet will easily slide off when you would like to use it. If you find the...
thingiverse
The Striker 4, in dual beam mode, rather than flasher mode, was a lot of fun fishing with. I could see my baited hook, and sinker, on the screens rather easily and all the Bluegills. I could see them chasing the sinker and I would pull the bait up...
thingiverse
Крепление в лодку эхолота Garmin Striker 4. ...Сделано так, чтобы не мешал управлять лодкой вёслами.
thingiverse
I designed this RAM mount for Garmin Striker Plus 4. It clips directly to the back of the unit and has a 1" ball mount which works with RAM mounts. the ball has been left slightly smaller than 1" to allow for heat shrink to be applied to the ball,...
thingiverse
After taking several measurements of the Garmin frame, I drew up a simple hood styled cover and then 3d printed it. The fit was good. For now I plan to either use velcro or double sided tape to to mount it to the Garmin. ... UPDATE: A longer version of...
thingiverse
This is my remix of the original sun shield for the Garmin Striker 4 (https://www.thingiverse.com/thing:2431935). I added a shield for the Striker 4 Plus as well. I was having some issues with the base separating from the side walls, so I added a...
thingiverse
... save you some time! The big advantage this sunshide has, is that you could just put over the Garmin Striker 4, without any tape, screws or anything else. Thank you jonnyg30 for this design! ... **Update 15.07.2018** Works absolut fine for my!
thingiverse
Garmin Striker 4 fish finder cover that snap-fits into place. Can be enlarged to fit the newer Pro series, but this one is meant for the original line. ... Use PETG (or paint it) for best weathering ability.
thingiverse
I wanted a clean mount for my Garmin Striker 4. This is a remix of the Scotty mount male end with supports. It has pilot holes for the 3 mounting screws in the base. ...I printed at 100% infill for strength.
thingiverse
Quick and dirty ball mount for Garmin Striker 4 Plus (CV/DV) sonar. The ball designed to fit rotating/tilting ball-grip arm from McMaster (part 5031T61). ...Please note that the ball is too large to fit a standard RAM mount!
thingiverse
I made these models for attaching a Garmin Striker 4 to the crossbar of my Minnesota 3, canoe. All these parts I have printed and are being used. The clip mount prints best with the face of the clip on the printer plater. This clip may need to...
cults3d
Used with the Striker 4 Swivel Mount (https://www.amazon.com/dp/B07C3TBGTM?psc=1&ref=ppx_yo2ov_dt_b_product_details) Box design to keep the battery out of the elements. Designed with the Milwaukee Battery adapter to fit I believe any Milwaukee...
thingiverse
Built out from my toprail [rod holder mounts](https://www.thingiverse.com/thing:4835566) to make rail mounts for a Garmin Striker 4 Vivid fishfinder (same size as Striker 4 Plus). Parts are specific to a Grumman 19' square stern aluminum canoe. ...
thingiverse
Downscaled the hood from the original design with 10 MM 60MM in total
cults3d
This is a remix of dergutehirte's sunshade remix for the Garmin Striker 4 (https://www.thingiverse.com/thing:3004062). The original designer was jonnyg30 (https://www.thingiverse.com/thing:2962608). Thanks guys for the designs. I prefer their design...
thingiverse
This is a remix of dergutehirte's sunshade remix for the Garmin Striker 4 (https://www.thingiverse.com/thing:3004062). The original designer was jonnyg30 (https://www.thingiverse.com/thing:2962608). Thanks guys for the designs. I prefer their design...
thingiverse
I needed a spacer for my Garmin Striker Plus 4 transducer to mate with a YakAttack SwitchBlade™ Transducer Deployment Arm (FFP-1001). ...I created a simple washer using the dimensions (20mm diameter, 4.5mm thick, 6.1mm diameter hole)
thingiverse
Using this adapter the Garmin Striker 4 (Plus and 4cv also) head unit can be mounted on a scotty mount (you still need the stem of the scotty #135 camera mount, or you have to make one)
thingiverse
This design is used to mount a Garmin Striker 4 transducer into a kayak. I had originally used the mounting sponge that came with the Striker 4 kit, but I found that in choppy waves the water in the mount sponge that enables the transducer to...
thingiverse
This is for the Garmin Striker/EchoMap 9". ... Swivel Version https://www.thingiverse.com/thing:4254970 SEAMS: Ensure they are NOT ALIGNED Pilot Holes for #8 Screws ARROW towards the User Mount and Base a connected with a 1.5" 1/4 Screw, base is...
thingiverse
I created this to fit my Brooklyn Kayak for a Garmin Striker 5cv transducer. It fits well and I have not had any issues. I hope it helps others with this brand of fishing Kayak. You can download and separate the pieces inside of Tinkercad if you need...
cults3d
I created this to fit my Brooklyn Kayak for a Garmin Striker 5cv transducer. It fits well and I have not had any issues. I hope it helps others with this brand of fishing Kayak. You can download and separate the pieces inside of Tinkercad if you need...
thingiverse
Looked all over the web for a mount for my Fishfinder but couldn't find one so I made it, it's not pretty, but it will do the job and is meant to fit in the ice fishing bundle from Garmin will update it once I make one and figure out what upgrades it...